Общий каталог Mitsubishi 2020 - 2021 - страница 697

Предыдущая страница Следующая страница

Навигация

OF THREADING

a How this section page is organized

zClassifiedaccordingtoexternalorinternalapplications. xSub-classifiedaccordingtoproductseries.

(Refertotheindexonthenextpage.)

FIGURE SHOWING THE TOOLING APPLICATION

uses illustrations and arrows to depict the available machining

applications,suchasexternalandinternalthreading.

TYPE OF TOOL HOLDER

indicates the initial letters for the order

numberandcuttingapplications.

STANDARDS FOR APPLICABLE INSERTS

TITLE OF PRODUCTINDICATION OF EXTERNAL indicatesstockstatus,dimensions,etc.
PRODUCT SECTION/INTERNAL APPLICATIONforapplicableinserts.
MMTITHREADINGMMT
TYPEa Minimum cutting diameter .500".a Available with a pressed breakerM-CLASS INSERTS
a Various insert types.for chip control.WITH 3-D CHIP BREAKERS
BORING BARS a Precision class insert for precisea Able to change lead angle by
MMTIthread forms.replacing the shim.
INSERTS
Internal threading
GAMF Fig.1 (Screw-on type)Fig.2 (Screw-on type)CoatedDimensions (mm)Total
15°Pitchdepth

Order Number IC S PDY PDX RE of cut Geometry

LDRED H LDRED mm thread/inch (mm)

DMIN ALFLF
GAMF DCON
15°Fig.3 (Clamp-on type)Fig.4 (Clamp-on type)Details of position A
Refer to the insert standards
PDXLF for dimensions PDX and PDY.
DMINLDREDLDRED LF LF
Right hand tool holder only.
**z
Order NumberInsertDimensions (inch)Fig.
Numberx
RDCON LF LDRED WF H DMIN Clamp Bridge Clamp Screw Stop Ring Shim ScrewShimWrench
MMTIR102-0.50-1.5-C
a1.5° .625 5.000 1.000 .340 .586 .500 –TS25 –––zTKY08F 1
MMTIR102-0.50-2.5-Ca MMT11IR2.5° .625 5.000 1.000 .340 .586 .500 –TS25 –––zTKY08F 1
MMTIR102-0.60-1.5-Ca ooooo 1.5° .625 6.000 1.250 .380 .586 .600 –TS25 –––zTKY08F 1
MMTIR102-0.60-2.5-Ca2.5° .625 6.000 1.250 .380 .586 .600 –TS25 –––zTKY08F 1
MMTIR103-0.75-1.5-Ca1.5° .625 6.000 1.500 .480 .586 .750 – CS350860T–––zTKY15F 2
MMTIR103-0.75-2.5-Ca2.5° .625 6.000 1.500 .480 .586 .750 – CS350860T–––zTKY15F 2
MMTIR123-0.90-1.5-CMMT16IR1.5° .750 7.000 1.500 .510 .711 .900 SETK51 SETS51CR4 HFC03006 CTI32TP15 zTKY15F3
a oooooxHKY20R
MMTIR163-1.15-1.5-Ca1.5° 1.000 10.000 2.500 .660 .937 1.150 SETK51 SETS51CR4 HFC03006 CTI32TP15 zxTKY15FHKY20R 3
MMTIR203-1.45-1.5-Ca1.5° 1.250 10.000 2.000 .810 1.187 1.450 SETK51 SETS51CR4 HFC03006 CTI32TP15 zTKY15F4
xHKY20R
MMTIR124-0.95-1.5-Ca1.5° .750 7.000 2.000 .610 .711 .950 –TS43 –––zTKY15F 2
MMTIR124-0.95-2.5-Ca2.5° .750 7.000 2.000 .610 .711 .950 –TS43 –––zTKY15F 2
MMTIR164-1.20-1.5-CMMT22IR1.5° 1.000 8.000 1.500 .700 .937 1.200 SETK61 SETS61CR5 HFC04008 CTI43TP15 zTKY20F4
Ga oooooxHKY25R
MMTIR204-1.50-1.5-Ca1.5° 1.250 10.000 2.000 .860 1.187 1.500 SETK61 SETS61CR5 HFC04008 CTI43TP15 zxTKY20FHKY25R 4
MMTIR244-1.75-1.5-Ca1.5° 1.500 12.000 2.500 .980 1.437 1.750 SETK61 SETS61CR5 HFC04008 CTI43TP15 zTKY20F4
xHKY25R
Note 1) Select and use an alternate shim from list below (sold separately), dependant on the lead angle.
• The screw-on type has no shim. The holder has an in-built lead angle. Please select a holder with the appropriate lead angle.
• The minimum cutting diameter (DMIN) indicates the prepared hole diameter, not the nominal thread diameter.
* Clamp Torgue (lbf-in) : TS25=8.9, CS350860T=31, SETS51=31, TS43=31, SETS61=44, HFC03006=13, HFC04008=19
SHIM
Stock InclinationStock Inclination
Lead AngleOrder NumberAngle ApplicableLead AngleAngle Order Number Applicable
(%°)R(' °) Holder(%°)R ('°)Holder
–1.5°CTI32TN15a–3°–1.5°a –3° CTI43TN15
–0.5°CTI32TN05a–2°–0.5°a –2° CTI43TN05Insert
0.5°CTI32TP05–1° MMTIR0.5°–1° CTI43TP05 MMTIRInclination
aaAngleShim
1.5°CTI32TP15a0° oo3- ooo1.5°a CTI43TP15 0° oo4-ooo(' °)
2.5°CTI32TP25a1° -oo-C2.5°a CTI43TP25 1° -oo-C
3.5°CTI32TP35a2°3.5°a CTI43TP35 2°
4.5°CTI32TP45a3°4.5°a CTI43TP45 3°
Standard shim delivered with the holder.
RECOMMENDED CUTTING CONDITIONS
Work MaterialHardnessGrade Cutting Speed (SFM)Work MaterialHardnessGrade Cutting Speed (SFM)
PVP10MF490 (230─755)SVP10MF150 (50─230 )
Mild Steel<180HBVP15TF330 (195─460)Heat-Resistant Alloy─VP15TF100 (65─130 )
VP20RT260 (195─330)VP20RT
Carbon SteelVP10MF460 (260─655)VP10MF195 (130 ─260)
Alloy Steel180─280HBVP15TF330 (195─460)Titanium Alloy─VP15TF)
VP20RT260 (195─330)VP20RT150 (80─210
M Stainless Steel200HBVP15TF260 (130─395 )H Heat-Treated Alloy45─55HRCVP10MF165 (100 ─230)
<VP20RTVP15TF130 (65─195 )
Tensile StrengthVP10MF460 (260 ─655)
K Gray Cast Iron
<350MPaVP15TF295 (195─395 )
a : USA Stock s : Stocked in JapanHOW TO SELECT A SHIMG012
G026 <5 inserts in one case>MMT SERIES ORDER NUMBERG020
LEGEND FOR STOCK
STATUS MARK
is shown on the left hand page
ofeachdouble-pagespread.
PRODUCT STANDARDS
indicates order numbers, stock status
(perright/lefthand),applicableinserts,
holderdimensions,andspareparts.
MMT11IRA60-S0.5 ─ 1.5 48 ─166.353.04 0.80.90.03─ Partial formPNA 60°
sPDX
MMT16IRA60-Sa0.5 ─ 1.5 48 ─169.525 3.440.80.90.03─RE
MMT16IRG60-Sa1.75─ 3.0 14 ─89.525 3.441.21.70.11─PDY
IC
S
MMT11IRA55-S48 ─166.353.04 0.80.90.07─ Partial formPNA 55°
sPDX
MMT16IRA55-Ss48 ─169.525 3.440.80.90.07─RE
MMT16IRG55-Ss14 ─89.525 3.441.21.70.21─PDY
IC
S
MMT11IR100ISO-Ss1.06.353.04 0.60.70.060.58 Full form
MMT11IR125ISO-Ss1.256.353.04 0.80.90.080.72
MMT11IR150ISO-Ss1.56.353.04 0.81.00.100.87PNA
60°
MMT16IR100ISO-Sa s1.09.525 3.440.60.70.060.58PDX
MMT16IR125ISO-S1.259.525 3.440.80.90.080.72RE
a sPDY
MMT16IR150ISO-Sa s1.59.525 3.440.81.00.100.87
MMT16IR175ISO-Sa s1.759.525 3.440.91.20.111.01
MMT16IR200ISO-Sa s2.09.525 3.441.01.30.131.15ICG
MMT16IR250ISO-S2.59.525 3.441.11.50.171.44S
a s
MMT16IR300ISO-Sa s3.09.525 3.441.11.50.201.73
MMT16IR160UN-Sa169.525 3.440.91.10.110.92 Full formPNA 60°
MMT16IR140UN-S149.525 3.440.91.20.121.05PDX
aRE
MMT16IR120UN-Sa129.525 3.441.11.40.141.22PDY
IC
S
MMT16IR190W-Ss199.525 3.440.81.00.180.86 Full formPNA 55°
MMT16IR140W-Ss149.525 3.441.01.20.251.16RE PDX
PDY
MMT16IR110W-Ss119.525 3.441.11.50.321.48
IC
S
MMT16IR190BSPT-S199.525 3.440.80.90.180.86 Full formPNA 55°
sPDX
MMT16IR140BSPT-Ss149.525 3.441.01.20.251.16RE
MMT16IR110BSPT-Ss119.525 3.441.11.50.321.48PDY
IC
S
IDENTIFICATION
MMT16 I R100ISO S
M-class inserts with
S 3-D chip breakers
DesignationHand of ToolPitchThreading Type
R Right60 Partial Profile 60°
100 1.0 mm0.5─1.5 mm
Diameter of Application125 1.25 mmA or55 Partial Profile 55°
Inscribed Circle 48─16 thread/inchISO ISO Metric
(mm) E External150 1.5 mm1.75─3.0 mmW Whitworth for BSW, BSP
6.35 11 I Internal175 1.75 mmG orBSPT BSPT
9.525 16200 2.0 mm14─8 thread/inchUN American UN
250 2.5 mm
300 3.0 mm
CUTTING DEPTH GUIDEG017SPARE PARTSN001TECHNICAL DATAG027 P001
PAGE REFERENCE
·SPARE PARTS
indicates reference pages, including the above,
ontherighthandpageofeachdouble-pagespread.
RECOMMENDED CUTTING CONDITIONS
foreachworkmaterialclassification,indicatesrecommended
cutting conditions according to the ISO categories for
cuttinggrades,P,M,K,S,andH.

a To Order : Forholder,pleasespecifyordernumberandhandoftool(right/left). Forinsert,pleasespecifyinsertnumberandgrade.