Общий каталог Tungaloy 2020 - 2021 - страница 501

Предыдущая страница Следующая страница

Навигация

WF GAMP WF BH B GradeInsertExt. ToolholderInt. ToolholderThreadingGroovingMiniature toolMilling cutterEndmillDrilling toolTooling SystemUser's GuideIndex CNR/L A Clamp-on internal threading toolholder (alternative clamping of screw-on or clamp-on only for DT type) LFDMINGAMFLHL3 H DCONMS B Reinforced carbide (Tsuppari-Ichiban only) Right hand (R) shown.Tsuppari-Ichiban shank.C Designation Material DMIN DCONMS WF LF LH L3 H B GAMF GAMP Insert TCNR0020R16DT Reinforced 24 20 14 200 30 49 18 - 15 1 16IR... TCNR0025S16DT Reinforced 29 25 16.5 250 38 64 23 - 15TCNR0025S22DTReinforced302518.2250386423-15CNR/L0020P16Steel24201417030-181915116IR...122IR...116IR/L...D CNR/L0025R16 Steel 29 25 16.5 200 38 - 23 24 15 1 16IR/L... CNR/L0032S16 Steel 37 32 20.1 250 48 - 30 31 15 1 16IR/L... CNR/L0025R22CNR/L0032S22CNR0040T27Steel 30 25 18.2 200 38Steel383221.925048Steel464026.930060---2324 153031153738.5101 22IR/L...122IR/L...127IR ... E Note: A clamp set consists of a clamp and a clamping screw. A shim set consists of a shim and a shim screw to secure the shim to the shank. Standard shims can be used on both right- and left-hand toolholders. Please use either of the sides depending on the tool hand. When using DT type, please remove either the clamp set or the insert clamping screw.SPARE PARTS F Designation Clamp set Clamping screw Shim screw Shim Shim set R Shim set L Wrench 1 Wrench 2 Wrench 3 TCNR002**16DT CSP16 CSTB-3.5ST DTS5-3.5 A16-1DT - - P-3.5 T-15F - TCNR0025S22DT CSP22 CSTB-4ST DTS6-4 GX22-1DT - - P-4CNR/L**16CSP16---A16-1A16-1-CNR/L**22CSP22---NXN22-1NXE22-1-T-15FT-20FT-15F-T-20F-G CNR0040T27 CSP27 - - - NXN27-1 NXE27-1 P-4 - - H MTVNR/L-5 External threading toolholder, for single-sided lay down inserts LH I LF 7° Right hand (R) shown. J Designation B H LF LH WF Insert MTVNR-2525M5 25 25 152 39 31.8 L535B**EXT-FC MTVNR-3232M5 32SPARE PARTS 32 178 39 38.1 L535B**EXT-FC K Designation Shim Lock pin Clamp Clamping screw Wrench MTVNR... LS53NOFORMEXT NL-58 TC-250 STC-11 1/8HEX L M Reference pages: CNR/L: Inserts → E010, E014, E016 - E027, Standard cutting conditions → E050 Tungaloy E037