Общий каталог Tungaloy 2020 - 2021 - страница 1632

Предыдущая страница Следующая страница

Навигация

Parts for ToolsTechnicalReference *Pitch (mm)*Pitch (mm) TPI (Thread per Inch)TPI (Thread per Inch) User’s Guide - Technical Reference Shim replacement method of S T- t y p e tools Type of shim and the compensation value of lead angle Compensated leadThe designation of the shimangles-2° -1° 0° 1° 2° 3° 4° and compensated lead Shim ᮀᮀᮀ-98 ᮀᮀᮀ-99 ᮀᮀᮀ-0 ᮀᮀᮀ-1 ᮀᮀᮀ-2 ᮀᮀᮀ-3 ᮀᮀᮀ-4 angles are shown in the table. Note: The last numeral of the shim designation is the compensated lead angle. Clamp-on type toolholders ᭿ Toolholders and applicable shims Shim Toolholder designation R L Screw-on / clamp-on dual toolholders CER/Lᮀᮀᮀᮀᮀ16-T AE16-ᮀ AN16-ᮀ ShimToolholder designation CER/Lᮀᮀᮀᮀᮀ22-T NXE22-ᮀ NXN22-ᮀ R L CER/Lᮀᮀᮀᮀᮀ27-T NXE27-ᮀ NXN27-ᮀ CER/Lᮀᮀᮀᮀᮀ16DT AE16-ᮀDT AN16-ᮀDT CNR/Lᮀᮀᮀᮀᮀ16 AN16-ᮀ AE16-ᮀ CER/Lᮀᮀᮀᮀᮀ22DT GXE22-ᮀDT GXN22-ᮀDT CNR/Lᮀᮀᮀᮀᮀ22 NXN22-ᮀ NXE22-ᮀ TCNR/Lᮀᮀᮀᮀᮀ16DT AN16-ᮀDT AE16-ᮀDT CNR/Lᮀᮀᮀᮀᮀ27 NXN27-ᮀ NXE27-ᮀ TCNR/Lᮀᮀᮀᮀᮀ22DT GXN22-ᮀDT GXE22-ᮀDT B-CER/Lᮀᮀᮀ16 AE16-ᮀ AN16-ᮀ Note: Standard shim is AE16-1DT or GX22-1DT. Other types are optional. Note: Standard shim is ᮀᮀᮀᮀᮀ-1. Other types are optional. Shim selection guide for screw-on / clamp-on dual ST-type tools Need special toolholders 7 AE16-4DT AE16-3DT AE16-2DT 6 4 AN16-4DT AN16-3DT AN16-2DT GXE22-4DT GXE22-3DT GXE22-2DT 5 5 GXN22-4DT GXN22-3DT GXN22-2DT 4 6 ᭹ List of exchangeable shims 3 Standard shim 8 Designation D30 Designation D30 Designation D30 Designation D30 21 A16-1DTGX22-1DT(Used for both externaland internal )10121624 β3 = 4° AE16-4DT 䖃 AN16-4DT 䖃 GXE22-4DT 䖃 GXN22-4DT 䖃β3 = 3°AE16-3DT䖃AN16-3DT䖃 GXE22-3DT䖃 GXN22-3DT䖃β3 = 2°AE16-2DT䖃AN16-2DT䖃 GXE22-2DT䖃 GXN22-2DT䖃β3 = 1°Standard shim A16-1DT䖃A16-1DT䖃 GX22-1DT䖃 GX22-1DT䖃 50 100 150 β3 = 0° AE16-0DT 䖃 AN16-0DT 䖃 GXE22-0DT 䖃 GXN22-0DT 䖃 Pich diameter (ød) β3 = -1° AE16-99DT 䖃 AN16-99DT 䖃 GXE22-99DT 䖃 GXN22-99DT 䖃 β3 = -2° AE16-98DT 䖃 AN16-98DT 䖃 GXE22-98DT 䖃 GXN22-98DT 䖃 * For the multi start thread lead (multiplied by the pitchand No. of threads) Applicable CER--16DT CEL--16DT CER--22DT CEL--22DTtoolholdersTCNL--16DTTCNR--16DTTCNL--22DTTCNR--22DT Shim selection guide for clamp-on type ST-tools Need special toolholders 7 AE16-4, AN16-4 AE16-3, AN16-3 AE16-2, AN16-2 6 4 NXE22-4, NXN22-4 NXE22-3, NXN22-3 NXE22-2, NXN22-2 5 5 NXE27-4, NXN27-4 NXE27-3, NXN27-3 NXE27-2, NXN27-2 4 6 ᭹ List of exchangeable shims 3 Standard shim 8 Designation D30 Designation D30 Designation D30 Designation D30 Designation D30 Designation D30 21 A16-1NXE22-1, NXN22-1NXE27-1, NXN27-110 β3 = 4° AE16-4 䖃 AN16-4 䖃 NXE22-4 䖃 NXN22-4 䖃 NXE27-4 NXN27-412β3 = 3°AE16-3䖃AN16-3䖃NXE22-3䖃NXN22-3䖃NXE27-3NXN27-31624β3 = 2°AE16-2䖃AN16-2䖃NXE22-2䖃NXN22-2䖃NXE27-2NXN27-2β3 = 1° Standard shim A16-1䖃A16-1䖃NXE22-1䖃NXN22-1䖃NXE27-1䖃NXN27-1䖃 50 100Pich diameter (ød)150 β3 = 0° AE16-0 䖃 AN16-0 䖃 NXE22-0 䖃 NXN22-0 䖃 NXE27-0 NXN27-0β3 = -1°AE16-99䖃AN16-99䖃NXE22-99䖃NXN22-99 䖃NXE27-99NXN27-99β3 = -2°AE16-98䖃AN16-98䖃NXE22-98䖃NXN22-98 䖃NXE27-98NXN27-98 * For the multi start thread lead (multiplied by the pitchand No. of threads) ApplicabletoolholdersCER--16T CEL--16TCNL--16CNR--16B-CER--16 B-CEL--16CER--22TCNL--22CEL--22TCNR--22CER--27TCNL--27CEL--27TCNR--27 䖃 : Line up L044 www.tungaloy.com