Общий каталог Tungaloy 2020 - 2021 - страница 1155

Предыдущая страница Следующая страница

Навигация

Zd Zd Zd C CC GradeInsertExt. ToolholderInt. ToolholderThreadingGroovingMiniature toolMilling cutterEndmillDrilling toolTooling SystemUser's GuideIndex A Guidelines for programming Z-axis plunging depth Zd (mm) in 45° chamfering of holeHole dia.Size of chamfering C (mm)ød (mm)0.511.52345 (45°) B 5 0.7 1.2 1.7 2.2 3.2 - - 6 1.2 1.7 2.2 2.7 3.7 - - 6.8 1.6 2.1 2.6 3.1 4.1 - - 8 2.2 2.7 3.2 3.7 4.7 - -8.52.42.93.43.94.9--103.23.74.24.75.76.77.710.23.33.84.34.85.86.87.8 45° C 12 4.2 4.7 5.2 5.7 6.7 7.7 8.7 14 5.2 5.7 6.2 6.7 7.7 8.7 9.7 16 6.2 6.7 7.2 7.7 8.7 9.7 10.7 17.5 6.9 7.4 7.9 8.4 9.4 10.4 11.4208.28.79.29.710.711.712.7218.79.29.710.211.212.213.22410.210.711.211.712.713.714.7ødTool: ECC31005R-45 D 30 13.2 13.7 14.2 14.7 15.7 16.7 17.7 Note: When the hole depth is smaller than the Z-axis 33 14.7 15.2 15.7 16.2 17.2 18.2 19.2 plunging depth (Zd), special care should be 36 16.2 16.7 17.2 17.7 18.7 19.7 - taken to avoid an interference between the 42 19.2 19.7 20.2 - - -Z-axis plunging depth Zd (mm) in 30° chamfering of hole-tool's front end and the bottom of the hole. E Hole dia. Size of chamfering C (mm) ød (mm) 0.5 1 1.5 2 2.5 3 3.5 5 0.6 1.1 1.6 2.1 - - -60.91.41.92.4---6.81.11.62.12.6--- (60°) F 8 1.4 1.9 2.4 2.9 - - - 8.5 1.6 2.1 2.6 3.1 - - - 10 2 2.5 3 3.5 4 4.5 5 30° 10.2 2.1 2.6 3.1 3.6 4.1 4.6 5.1 12 2.6 3.1 3.6 4.1 4.6 5.1 5.6163.74.24.75.25.76.26.717.54.24.75.25.76.26.77.2 G 20 4.9 5.4 5.9 6.4 6.9 7.4 7.9 ød 21 5.2 5.7 6.2 6.7 7.2 7.7 8.2 24 6.1 6.6 7.1 7.6 8.1 8.6 9.1 30 7.8338.7369.53810.18.3 8.8 9.39.29.710.21010.51110.611.111.69.810.711.512.110.311.21212.610.811.712.5 Tool: ECC31005R-6013.1Note: When the hole depth is smaller than the Z-axisH 42 11.2 11.7 12.2 12.7 13.2 13.7 14.2 plunging depth (Zd), special care should be 46 12.4 12.9 13.4 13.9 14.4 - - taken to avoid an interference between the 48 13 13.5 14 14.5 - - - tool's front end and the bottom of the hole. 52 14.1 - - - - - -Z-axis plunging depth Zd (mm) in 60° chamfering of hole I Hole dia. Size of chamfering C (mm) (30°) ød (mm) 0.5 1 1.5 2 2.5 3 3.5 4 5 0.8 1.3 1.8 2.3 2.8 - - -61.72.22.73.23.7---6.82.42.93.43.94.4---83.43.94.44.95.4--- 60° J 8.5 3.8 4.3 4.8 5.3 5.8 - - - 10 5.1 5.6 6.1 6.6 7.1 7.6 8.1 8.6 10.2 5.3 5.8 6.3 6.8 7.3 7.8 8.3 8.8 12 6.9 7.4 7.9 8.4 8.9 9.4 9.9 10.41610.310.811.311.812.312.813.313.817.511.612.112.613.113.614.114.615.12013.714.214.715.215.716.216.717.2ødTool: ECC31005R-30K 21 14.6 15.1 15.6 16.1 16.6 17.1 17.6 18.1 Note: When the hole depth is smaller 24 17.2 17.7 18.2 18.7 19.2 19.7 20.2 20.7 than the Z-axis plunging depth 30 22.4 22.9 23.4 23.9 24.4 24.9 25.4 - (Zd), special care should be 33 24.9 25.4 - - - - - - taken to avoid an interferencebetween the tool's front end andthe bottom of the hole.L M Tungaloy I095