Общий каталог Mitsubishi 2020 - 2021

Каталог Mitsubishi Materials запасные части

Каталог Mitsubishi Materials резьбонарезной инструмент

Каталог Mitsubishi Materials СНП с CBN и PCD для токарной обработки

Каталог Mitsubishi Materials сверлильные инструменты

Каталог Mitsubishi Materials расточной инструмент

Каталог Mitsubishi Materials пластины для точения

CARBIDE RECOMMENDED CUTTING CONDITIONS

Work M	aterial	Carbon steel, A Alloy tool steel, Precipitation h	lloy steel (180 Pre-hardened ardening stainl	─280HB) steel, ess steel	Hardened stee	l(45─55HRC)		Copper, Coppe	r alloy
RE (mm)	LU (mm)	Revolution (min-1)	Table feed (mm/min)	Depth of cut ap(mm)	Revolution (min-1)	Table feed (mm/min)	Depth of cut ap(mm)	Revolution (min-1)	Table feed (mm/min)	Depth of cut ap(mm)
	10	36000	6000	0.12	29000	3800	0.12	29000	3800	0.24
	15	32000	4500	0.1	26000	2900	0.1	26000	2900	0.2
	20	26000	3200	0.07	21000	2000	0.07	21000	2000	0.14
1.25	25	12000	1400	0.06	8000	720	0.06	8000	720	0.12
	30	8000	900	0.04	8000	700	0.04	8000	700	0.08
	35	8000	800	0.02	8000	640	0.02	8000	510	0.04
	6	32000	7000	0.15	26000	4500	0.15	22000	3800	0.3
	10	32000	7000	0.15	26000	4500	0.15	22000	3800	0.3
	16	32000	5000	0.1	26000	3200	0.1	22000	2700	0.2
	20	27000	3800	0.1	22000	2400	0.1	22000	2400	0.2
1.5	25	21000	2700	0.08	17000	1700	0.08	17000	1700	0.16
	30	10000	700	0.08	6000	560	0.08	6000	560	0.16
	35	6000	700	0.06	6000	560	0.06	6000	560	0.12
	40	6000	600	0.04	6000	480	0.04	6000	480	0.08
	15	27500	4400	0.13	22000	2800	0.13	18000	2300	0.26
	25	23000	3600	0.1	18000	2200	0.1	18000	2200	0.2
1.75	35	10000	1400	0.08	10000	1100	0.08	10000	1100	0.16
	45	7500	900	0.04	7500	720	0.04	7500	720	0.08
	10	24000	6000	0.2	19000	3800	0.2	16000	3200	0.4
	20	24000	3800	0.15	19000	2400	0.15	16000	2000	0.3
2	30	20000	3000	0.1	16000	1900	0.1	16000	1900	0.2
	40	12000	1700	0.1	12000	1400	0.1	12000	1400	0.2
	50	8000	1000	0.05	8000	800	0.05	8000	800	0.1
	20	22000	6000	0.2	18000	3800	0.2	13000	2800	0.4
	25	22000	4400	0.2	18000	2800	0.2	13000	2000	0.4
2.5	30	22000	3800	0.15	18000	2400	0.15	13000	1700	0.3
	40	22000	3600	0.1	18000	2300	0.1	13000	1600	0.2
	20	20000	6000	0.2	16000	3800	0.2	11000	2600	0.4
	30	20000	6000	0.2	16000	3800	0.2	11000	2600	0.4
3	40	20000	4500	0.15	16000	2800	0.15	11000	2000	0.3
	50	20000	3000	0.15	16000	1900	0.15	11000	1300	0.3
Depth	of cut					RE (RE RE (RE>1)
							ap			RE : Radius

Note 1) When the inclination angle of machined surface is high, or when machining at high loads; such as in corners, reduce the revolution and feed rate. Note 2) The use of oil mist is recommended when machining with small diameter. Note 3) The revolution and feed rate can be increased at small depths of cut (ap). Note 4) Cutting conditions may differ considerably due to the overhang, depth of cut and machine tool condition. Please use the table above as a reference starting point. Note 5) For hardened steel over 55 HRC, use VF2XLB. Note 6) For cutting conditions for austenitic stainless steel and titanium alloy, use the high hardness steel (45-55 HRC) table but reduce the spindle speed by 40% and the feed rate by 55%.

Общий каталог Mitsubishi 2020 - 2021 - страница 871

Навигация

Общий каталог Mitsubishi 2020 - 2021 - страница 871

Навигация

Отправьте заявку

На подбор необходимой оснастки и оборудования