Общий каталог Mitsubishi 2020 - 2021 - страница 1203
Навигация
Каталог Mitsubishi Materials запасные части
Каталог Mitsubishi Materials резьбонарезной инструмент
Каталог Mitsubishi Materials СНП с CBN и PCD для токарной обработки
Каталог Mitsubishi Materials сверлильные инструменты
Каталог Mitsubishi Materials расточной инструмент
Каталог Mitsubishi Materials пластины для точения 
y Wet Cutting Condition
| Work Material | Hardness | 1st Recommendation | 2nd Recommendation | vc (SFM) | Finish Cuttin | g |
| fz(IPT) | ap | |||||
| P | L Breaker | |||||
| Mil Sl | MP6120 | VP15TF | 490 (330─655) | .006 (.004─.008) | ||
| d tee | 80 | MP6130 | VP20RT | 490 (330─655) | .006 (.004─.008) | |
| Carbon Steel | 180─350HB | MP6120 | VP15TF | 395 (260─525) | .006 (.004─.008) | |
| Alloy Steel | MP6130 | VP20RT | 395 (260─525) | .006 (.004─.008) | ||
| MP6120 | VP15TF | 395 (260─525) | .006 (.004─.008) | |||
| Alloy Tool Steel | (Annealing) | MP6130 | VP20RT | 395 (260─525) | .006 (.004─.008) | |
| MP6120 | VP15TF | 330 (260─395) | .006 (.004─.008) | |||
| Pre-Hardened Steel | 35─45HRC | MP6130 | VP20RT | 330 (260─395) | .006 (.004─.008) | |
| M | L Breaker | |||||
| Atiti Stil Stl | MP7130 | VP15TF | 425 (260─590) | .006 (.004─.008) | ||
| usenc aness ee | MP7140 | VP20RT | 425 (260─590) | .006 (.004─.008) | ||
| MP7130 | VP15TF | 330 (260─490) | .006 (.004─.008) | |||
| Austenitic Stainless Steel | > 200HB | MP7140 | VP20RT | 330 (260─490) | .006 (.004─.008) | |
| Dl Stil Stl | MP7130 | VP15TF | 330 (260─490) | .006 (.004─.008) | ||
| upex aness ee | MP7140 | VP20RT | 330 (260─490) | .006 (.004─.008) | ||
| Precipitation Hardening | MP7130 | VP15TF | 295 (165─460) | .006 (.004─.008) | ||
| Stainless Steel | < 450HB | MP7140 | VP20RT | 295 165─460 | 006 004─008 | |
| () | . (..) | . | ||||
| K | L Breaker | |||||
| GCtI | MC5020 | ─ | 590 (525─655) | .006 (.004─.008) | ||
| ray as ron | a | VP15TF | VP20RT | 425 (330─525) | .006 (.004─.008) | |
| MC5020 | ─ | 590 (525─655) | .006 (.004─.008) | |||
| Ductile Cast Iron | VP15TF | VP20RT | 425 (330─525) | .006 (.004─.008) | ||
| MC5020 | ─ | 590 (525─655) | .006 (.004─.008) | |||
| Ductile Cast Iron | VP15TF | VP20RT | 360 (260─460) | .006 (.004─.008) | ||
| N | L Breaker | |||||
| Aluminum Alloy | ─ | TF15 | ─ | 1640 (655─3280) | .006 (.004─.008) | |
| S | L Breaker | |||||
| MP9120 | VP15TF | 165 (130─195) | .002 (.002─.004) | |||
| Titanium Alloy | ─ | MP9130 | VP20RT | 165 (130─195) | .002 (.002─.004) | |
| MP9120 | VP15TF | 130 (65─165) | .002 (.002─.004) | |||
| Heat Resistant Alloy | ─ | MP9130 | VP20RT | 130 (65─165) | .002 (.002─.004) |
Note 1) Refer to the table above and set the cutting conditions to match the application. Note 2) Wet cutting is recommended, when focusing on the surface finish. (Life is lower than dry cutting.)