Общий каталог Mitsubishi 2020 - 2021 - страница 1079
Навигация
Каталог Mitsubishi Materials запасные части
Каталог Mitsubishi Materials резьбонарезной инструмент
Каталог Mitsubishi Materials СНП с CBN и PCD для токарной обработки
Каталог Mitsubishi Materials сверлильные инструменты
Каталог Mitsubishi Materials расточной инструмент
Каталог Mitsubishi Materials пластины для точения 
iMX-B4HV/iMX-B4HV-E
Ball nose head, 4 flute, Irregular curve (With/Without coolant hole)
CARBIDE
RECOMMENDED CUTTING CONDITIONS
y Shoulder Milling (L/D=3)
Other than the L/D = 3, use following recommended cutting conditions by multiplying the J003 page correction factor by overhang length. (inch)
| W Ma | ork terial | Carbon Stee Pre-hardene | l, Alloy Ste d Steel | el, Mild Steel, | Austenitic S Ferritic and Cobalt Chro Titanium All | tainless Ste Martensitic mium Alloy, oy | el, Stainless Ste | el, | |||||
| Inclinati | on Angle | % | 15° | %> | 15° | Depth of Cut | Width of Cut | % | 15° | %> | 15° | Depth of Cut | Width of Cut |
| R (mm) | E (inch) | Revolution n (min-1) | Feed Rate vf (IPM) | Revolution n (min-1) | Feed Rate vf (IPM) | ap | ae | Revolution n (min-1) | Feed Rate vf (IPM) | Revolution n (min-1) | Feed Rate vf (IPM) | ap | ae |
| .1875 | 10000 | 168.0 | 6700 | 75.0 | .038 | .100 | 7500 | 123.0 | 5000 | 52.0 | .038 | .100 | |
| 5 | .1969 | 9500 | 157.5 | 6400 | 71.7 | .039 | .100 | 7200 | 118.1 | 4800 | 49.9 | .039 | .100 |
| 6 | .2362 | 8000 | 156.8 | 5300 | 70.0 | .047 | .120 | 6000 | 117.6 | 4000 | 49.6 | .047 | .120 |
| .2500 | 7500 | 147.0 | 5000 | 66.0 | .050 | .120 | 5700 | 111.7 | 3700 | 45.9 | .050 | .120 | |
| .3125 | 6000 | 127.2 | 4000 | 56.0 | .063 | .160 | 4500 | 99.0 | 3000 | 42.0 | .063 | .160 | |
| 8 | .3150 | 6000 | 127.2 | 4000 | 56.0 | .063 | .160 | 4500 | 99.0 | 3000 | 42.0 | .063 | .160 |
| .3750 | 5000 | 122.0 | 3300 | 51.5 | .075 | .190 | 3800 | 95.8 | 2500 | 41.0 | .075 | .190 | |
| 10 | .3937 | 4800 | 117.1 | 3200 | 49.9 | .079 | .200 | 3600 | 90.7 | 2400 | 39.4 | .079 | .200 |
| 12.5 | .4921 | 3800 | 95.8 | 2500 | 39.0 | .098 | .240 | 2900 | 73.1 | 1900 | 31.2 | .098 | .240 |
| .5000 | 3800 | 95.8 | 2500 | 39.0 | .100 | .240 | 2800 | 70.6 | 1900 | 31.2 | .100 | .240 | |
| Depth | of Cut | ae |
ap
Note 1) The irregular helix flute end mill has a larger effect on controlling vibration when compared to standard end mills. However, if the rigidity of the machine or the work material installation is poor, vibration or abnormal sound can occur. In this case, please reduce the revolution and the feed rate proportionately, or set a lower depth of cut.
J Note 2) If the depth of cut is smaller, the revolution and the feed rate can be increased. %
Note 3) For stainless steel, titanium alloy and heat resistant alloy, the use of water-soluble coolant is effective. Note 4) % is the inclination angle of the machined surface.