Общий каталог Mitsubishi 2020 - 2021 - страница 713
Навигация
Каталог Mitsubishi Materials запасные части
Каталог Mitsubishi Materials резьбонарезной инструмент
Каталог Mitsubishi Materials СНП с CBN и PCD для токарной обработки
Каталог Mitsubishi Materials сверлильные инструменты
Каталог Mitsubishi Materials расточной инструмент
Каталог Mitsubishi Materials пластины для точения 
MMT STANDARD OF DEPTH OF CUT EXTERNAL (RADIAL INFEED)
yAPI Round Casing & Tubing
(inch)
| Pitch | Total | Number of Passes | Insert Type |
| (thread/ Cutting |
| inch) | Depth | 6 5 4 3 2 1 7 | 12 11 10 9 8 G-class ground inserts |
| 10 .056 .010 .009 .006 .006 .005 .005 .005 .004 .004 .002 | MMT16ER100APRD | ||
| 8 .071 .010 .009 .007 .006 .006 .006 .005 .005 .005 .005 .005 .002 | MMT16ER080APRD | ||
| yAmerican NPT | (inch) | ||
| Pitch | Total | Number of Passes | Insert Type |
| (thread/ Cutting | |||
| inch) | Depth | 6 5 4 3 2 1 7 | 15 14 13 12 11 10 9 8 G-class ground inserts |
| 27 | .026 .006 .005 .005 .004 .004 .002 | MMT16ER270NPT | |
| 18 | .040 .008 .006 .006 .005 .005 .004 .004 .002 | MMT16ER180NPT | |
| 14 | .052 .009 .007 .006 .006 .005 .005 .004 .004 .004 .002 | MMT16ER140NPT | |
| 11.5 .065 .009 .007 .007 .006 .006 .005 .005 .005 .005 .004 .004 .002 | MMT16ER115NPT | ||
| 8 | .095 .013 .011 .009 .008 .007 .006 .006 .006 .005 .005 .005 .004 .004 .004 .002 | MMT16ER080NPT | |
| yAmerican NPTF | |||
| (inch) | |||
| Pitch | Total | Number of Passes | Insert Type |
| (thread/ Cutting | |||
| inch) | Depth | 6 5 4 3 2 1 7 | 15 14 13 12 11 10 9 8 G-class ground inserts |
| 27 | .025 .006 .006 .004 .004 .003 .002 | MMT16ER270NPTF | |
| 18 | .039 .007 .006 .006 .005 .005 .004 .004 .002 | MMT16ER180NPTF | |
| 14 | .053 .009 .008 .006 .006 .005 .005 .004 .004 .004 .002 | MMT16ER140NPTF | |
| 11.5 .064 .009 .009 .007 .006 .005 .005 .005 .004 .004 .004 .004 .002 | MMT16ER115NPTF | ||
| 8 | .094 .013 .011 .009 .007 .007 .006 .006 .006 .005 .005 .005 .004 .004 .004 .002 | MMT16ER080NPTF |
G Note 1) Set the finishing allowance on a diameter at approx. .004 inch when using a full form insert.
- Please note the cutting depth and the number of passes when a nose radius of a partial or semi-full form insert or of an internal threading insert is small to prevent damage to the insert nose.
- Please set the cutting depth sufficiently deep enough on materials such as hardened steel or austenitic stainless steel to help prevent premature wear and chipping caused by the outer layer of the material.