Общий каталог Mitsubishi 2020 - 2021 - страница 1052
Навигация
Каталог Mitsubishi Materials запасные части
Каталог Mitsubishi Materials резьбонарезной инструмент
Каталог Mitsubishi Materials СНП с CBN и PCD для токарной обработки
Каталог Mitsubishi Materials сверлильные инструменты
Каталог Mitsubishi Materials расточной инструмент
Каталог Mitsubishi Materials пластины для точения 
CARBIDE
RECOMMENDED CUTTING CONDITIONS
y Shoulder Milling (L/D=3)
Other than the L/D = 3, use following recommended cutting conditions by multiplying the J003 page correction factor by overhang length. (inch)
| W Mat | ork erial | Carbon Stee Copper, Cop | l, Alloy Stee per Alloy | l, Mild Steel, | Pre-harden Alloy Steel, | ed Steel, C Alloy Tool S | arbon Steel, teel | Austenitic S Ferritic and Titanium Al | tainless Ste Martensitic loy | el, Stainless Ste | el, | ||
| D | C | Revolution | Feed Rate f | Depth of Cut | Width of Cut | Revolution | Feed Rate f | Depth of Cut | Width of Cut | Revolution | Feed Rate f | Depth of Cut | Width of Cut |
| (mm) | (inch) | n (min-1) | v (IPM) | ap | ae | n (min-1) | v (IPM) | ap | ae | n (min-1) | v (IPM) | ap | ae |
| .3750 | 5000 | 52.5 | .300 | .075 | 4000 | 28.8 | .300 | .075 | 3400 | 30.6 | .300 | .075 | |
| 10 | .3937 | 4800 | 50.4 | .315 | .079 | 3800 | 27.4 | .315 | .079 | 3200 | 28.8 | .315 | .079 |
| 12 | .4724 | 4000 | 42.0 | .378 | .094 | 3200 | 25.0 | .378 | .094 | 2700 | 25.1 | .378 | .094 |
| .5000 | 3700 | 38.9 | .400 | .100 | 3000 | 23.4 | .400 | .100 | 2500 | 23.3 | .400 | .100 | |
| .6250 | 3000 | 35.1 | .500 | .125 | 2400 | 21.6 | .500 | .125 | 2000 | 21.0 | .500 | .125 | |
| 16 | .6299 | 3000 | 35.1 | .504 | .126 | 2400 | 21.6 | .504 | .126 | 2000 | 21.0 | .504 | .126 |
| .7500 | 2500 | 29.3 | .600 | .150 | 2000 | 18.0 | .600 | .150 | 1700 | 17.9 | .600 | .150 | |
| 20 | .7874 | 2400 | 28.1 | .630 | .157 | 1900 | 17.1 | .630 | .157 | 1600 | 16.8 | .630 | .157 |
| 25 | .9843 | 1900 | 26.8 | .787 | .197 | 1500 | 13.5 | .787 | .197 | 1300 | 13.7 | .787 | .197 |
| 1.0000 | 1900 | 26.8 | .800 | .200 | 1500 | 13.5 | .800 | .200 | 1300 | 13.7 | .800 | .200 |
ae Depth of Cut ap
| W Ma | ork terial | Precipitation Cobalt Chro | Hardening mium Alloy | Stainless St | eel, | Heat Resist Inconel718 | ant Alloy | ||
| DC | Revolution | Feed Rate f | Depth of Cut | Width of Cut | Revolution | Feed Rate f | Depth of Cut | Width of Cut | |
| (mm) | (inch) | n (min-1) | v (IPM) | ap | ae | n (min-1) | v (IPM) | ap | ae |
| .3750 | 2500 | 18.0 | .300 | .075 | 1300 | 6.2 | .300 | .038 | |
| 10 | .3937 | 2400 | 17.3 | .315 | .079 | 1300 | 6.2 | .315 | .039 |
| 12 | .4724 | 2000 | 15.6 | .378 | .094 | 1100 | 5.9 | .378 | .047 |
| .5000 | 1900 | 14.8 | .400 | .100 | 990 | 5.3 | .400 | .050 | |
| .6250 | 1500 | 13.5 | .500 | .125 | 790 | 4.7 | .500 | .063 | |
| 16 | .6299 | 1500 | 13.5 | .504 | .126 | 790 | 4.7 | .504 | .063 |
| .7500 | 1200 | 10.8 | .600 | .150 | 660 | 4.0 | .600 | .075 | |
| 20 | .7874 | 1200 | 10.8 | .630 | .157 | 630 | 3.8 | .630 | .079 |
| 25 | .9843 | 950 | 8.6 | .787 | .197 | 500 | 3.0 | .787 | .098 |
| 1.0000 | 940 | 8.5 | .800 | .200 | 500 | 3.0 | .800 | .100 | |
| ae | |||||||||
| Depth | of Cut | ap |
Note 1) The irregular helix flute end mill has a larger effect on controlling vibration when compared to standard end mills. However, if the rigidity of the machine or the work material installation is poor, vibration or abnormal sound can occur. In this case, please reduce the revolution and the feed rate proportionately, or set a lower depth of cut. Note 2) If the depth of cut is smaller, the revolution and the feed rate can be increased.