Общий каталог Mitsubishi 2020 - 2021 - страница 1021
Навигация
Каталог Mitsubishi Materials запасные части
Каталог Mitsubishi Materials резьбонарезной инструмент
Каталог Mitsubishi Materials СНП с CBN и PCD для токарной обработки
Каталог Mitsubishi Materials сверлильные инструменты
Каталог Mitsubishi Materials расточной инструмент
Каталог Mitsubishi Materials пластины для точения 
DF2XLB
CARBIDE
RECOMMENDED CUTTING CONDITIONS
| Work M | aterial | Graphite | Table | feed | Copper, Cop | per alloy Table | feed | ||||
| RE | LU | Revolution | Depth of cut | Width of cut | Revolution | Depth of cut | Width of cut | ||||
| (mm) | (mm) | (min-1) | (mm/min) | (IPM) | ap (mm) | ae (mm) | (min-1) | (mm/min) | (IPM) | ap (mm) | ae (mm) |
| R0.1 | 0.5 | 40000 | 800 | 31.5 | 0.01 | 0.03 | 40000 | 800 | 31.5 | 0.003 | 0.02 |
| 2 | 40000 | 1200 | 47.2 | 0.03 | 0.08 | 40000 | 800 | 31.5 | 0.003 | 0.03 | |
| R0.15 | 3 | 40000 | 1200 | 47.2 | 0.03 | 0.08 | 40000 | 600 | 23.6 | 0.002 | 0.03 |
| 1 | 40000 | 1500 | 59.1 | 0.05 | 0.15 | 40000 | 2000 | 78.7 | 0.015 | 0.04 | |
| 2 | 40000 | 1500 | 59.1 | 0.05 | 0.12 | 40000 | 1300 | 51.2 | 0.01 | 0.04 | |
| R02 | 3 | 40000 | 1300 | 51.2 | 0.04 | 0.12 | 40000 | 800 | 31.5 | 0.005 | 0.04 |
| . | 4 | 40000 | 1300 | 51.2 | 0.04 | 0.1 | 32000 | 600 | 23.6 | 0.004 | 0.04 |
| 8 | 30000 | 800 | 31.5 | 0.03 | 0.1 | ─ | ─ | ─ | ─ | ─ | |
| 12 | 20000 | 450 | 17.7 | 0.03 | 0.08 | ─ | ─ | ─ | ─ | ─ | |
| 4 | 40000 | 1500 | 59.1 | 0.05 | 0.15 | 40000 | 800 | 31.5 | 0.01 | 0.05 | |
| R0.25 | 5 | 38000 | 1300 | 51.2 | 0.05 | 0.15 | 36000 | 700 | 27.6 | 0.008 | 0.05 |
| 8 | 30000 | 1000 | 39.4 | 0.04 | 0.12 | 28000 | 500 | 19.7 | 0.002 | 0.05 | |
| 2 | 40000 | 1800 | 70.9 | 0.07 | 0.2 | 40000 | 1500 | 59.1 | 0.03 | 0.06 | |
| 4 | 40000 | 1500 | 59.1 | 0.06 | 0.18 | 40000 | 1200 | 47.2 | 0.02 | 0.06 | |
| 5 | 40000 | 1500 | 59.1 | 0.06 | 0.17 | 40000 | 1100 | 43.3 | 0.015 | 0.06 | |
| R0.3 | 6 | 40000 | 1500 | 59.1 | 0.06 | 0.15 | 40000 | 1000 | 39.4 | 0.008 | 0.06 |
| 8 | 37000 | 1200 | 47.2 | 0.05 | 0.15 | 35000 | 800 | 31.5 | 0.005 | 0.06 | |
| 10 | 35000 | 1000 | 39.4 | 0.05 | 0.15 | ─ | ─ | ─ | ─ | ─ | |
| 16 | 22000 | 530 | 20.9 | 0.04 | 0.12 | ─ | ─ | ─ | ─ | ─ | |
| 6 | 40000 | 1700 | 66.9 | 0.08 | 0.2 | 40000 | 1500 | 59.1 | 0.02 | 0.08 | |
| R0.4 | 8 | 40000 | 1700 | 66.9 | 0.08 | 0.15 | 30000 | 1200 | 47.2 | 0.008 | 0.08 |
| 4 | 40000 | 2500 | 98.4 | 0.12 | 0.3 | 40000 | 2000 | 78.7 | 0.05 | 0.1 | |
| 6 | 40000 | 2500 | 98.4 | 0.1 | 0.3 | 40000 | 2000 | 78.7 | 0.03 | 0.1 | |
| 8 | 40000 | 2000 | 78.7 | 0.1 | 0.25 | 40000 | 1800 | 70.9 | 0.02 | 0.1 | |
| 10 | 40000 | 2000 | 78.7 | 0.1 | 0.2 | 33000 | 1400 | 55.1 | 0.01 | 0.1 | |
| R0.5 | 12 | 40000 | 2000 | 78.7 | 0.1 | 0.2 | 30000 | 1000 | 39.4 | 0.007 | 0.1 |
| 20 | 30000 | 1100 | 43.3 | 0.08 | 0.2 | ─ | ─ | ─ | ─ | ─ | |
| 30 | 20000 | 600 | 23.6 | 0.06 | 0.15 | ─ | ─ | ─ | ─ | ─ | |
| 40 | 15000 | 400 | 15.7 | 0.04 | 0.12 | ─ | ─ | ─ | ─ | ─ | |
| Depth | of cut | ae | ap |
Note 1) When high machining accuracy is needed, or work material becomes chipped, we recommend lowering feed rate. Note 2) Use a milling machine dedicated for graphite. Note 3) If rigidity of machine or work materials installation is very low, or chattering and noise are generated, reduce revolution and feed rate proportionately.