Общий каталог Mitsubishi 2020 - 2021 - страница 1015
Навигация
Каталог Mitsubishi Materials запасные части
Каталог Mitsubishi Materials резьбонарезной инструмент
Каталог Mitsubishi Materials СНП с CBN и PCD для токарной обработки
Каталог Mitsubishi Materials сверлильные инструменты
Каталог Mitsubishi Materials расточной инструмент
Каталог Mitsubishi Materials пластины для точения 
DF4XL
End mill, Long neck, 4 flute, For graphite
CARBIDE
RECOMMENDED CUTTING CONDITIONS
y Shoulder milling
| Work | Material | Graphite | Copper, Cop | per alloy | |||||||
| Table | feed | Table | feed | ||||||||
| DC | LU | Revolution 1 | Depth of cut | Width of cut | Revolution 1 | Depth of cut | Width of cut | ||||
| (mm) | (mm) | (min-) | (mm/min) | (IPM) | (mm) | (mm) | (min-) | (mm/min) | (IPM) | (mm) | (mm) |
| 6 | 30000 | 1300 | 51.2 | 1 | 0.05 | 30000 | 1300 | 51.2 | 1 | 0.05 | |
| 1 | 8 | 25000 | 1000 | 39.4 | 1 | 0.05 | 25000 | 1000 | 39.4 | 1 | 0.05 |
| 10 | 22000 | 700 | 27.6 | 1 | 0.05 | 22000 | 700 | 27.6 | 1 | 0.05 | |
| 15 | 10 | 25000 | 1200 | 47.2 | 1.5 | 0.075 | 21000 | 1000 | 39.4 | 1.5 | 0.075 |
| . | 16 | 18000 | 800 | 31.5 | 1.5 | 0.075 | 18000 | 800 | 31.5 | 1.5 | 0.075 |
| 10 | 22000 | 1500 | 59.1 | 2 | 0.1 | 16000 | 1100 | 43.3 | 2 | 0.1 | |
| 2 | 16 | 19000 | 1100 | 43.3 | 2 | 0.1 | 16000 | 930 | 36.6 | 2 | 0.1 |
| 20 | 16000 | 800 | 31.5 | 2 | 0.1 | 16000 | 800 | 31.5 | 2 | 0.1 | |
| 16 | 21000 | 1900 | 74.8 | 3 | 0.15 | 10600 | 960 | 37.8 | 3 | 0.15 | |
| 3 | 20 | 18000 | 1500 | 59.1 | 3 | 0.15 | 10600 | 890 | 35.0 | 3 | 0.15 |
| 30 | 14000 | 1000 | 39.4 | 3 | 0.15 | 10600 | 760 | 29.9 | 3 | 0.15 | |
| 4 | 20 | 18000 | 2400 | 94.5 | 4 | 0.4 | 8000 | 1100 | 43.3 | 4 | 0.4 |
| 40 | 13000 | 1500 | 59.1 | 4 | 0.4 | 8000 | 920 | 36.2 | 4 | 0.4 | |
| 6 | 30 | 14000 | 3200 | 126.0 | 6 | 0.6 | 5300 | 1200 | 47.2 | 6 | 0.6 |
| 8 | 30 | 10500 | 2900 | 114.2 | 8 | 0.8 | 4000 | 1100 | 43.3 | 8 | 0.8 |
| 10 | 30 | 8700 | 2600 | 102.4 | 10 | 1.0 | 3200 | 960 | 37.8 | 10 | 1.0 |
| 12 | 30 | 7200 | 2200 | 86.6 | 12 | 1.2 | 2650 | 800 | 31.5 | 12 | 1.2 |
| Depth | of cut | DC) | DC : Dia. |
I
Note 1) When high machining accuracy is needed, or work material becomes chipped, we recommend lowering feed rate. Note 2) Use a milling machine dedicated for graphite. Note 3) If rigidity of machine or work materials installation is very low, or chattering and noise are generated, reduce revolution and feed rate proportionately.