Общий каталог Mitsubishi 2020 - 2021

Каталог Mitsubishi Materials запасные части

Каталог Mitsubishi Materials резьбонарезной инструмент

Каталог Mitsubishi Materials СНП с CBN и PCD для токарной обработки

Каталог Mitsubishi Materials сверлильные инструменты

Каталог Mitsubishi Materials расточной инструмент

Каталог Mitsubishi Materials пластины для точения

CARBIDE

RECOMMENDED CUTTING CONDITIONS

Work Material	Harden AISI H1	ed steel ( 3	45─55H	RC)			Harden AISI D2	ed steel	(55─62	HRC)			Harden AISI W1	ed steel , AISI M	(62─70 2	HRC)
RE	%	15°	%>	15°	Depth of cut	Depth of cut	%	15°	%>	15°	Depth of cut	Depth of cut	%	15°	%>	15°	Depth of cut	Depth of cut
(mm)	Revolution (min-1)	Table feed (mm/min)	Revolution (min-1)	Table feed (mm/min)	ap (mm)	ae (mm)	Revolution (min-1)	Table feed (mm/min)	Revolution (min-1)	Table feed (mm/min)	ap (mm)	ae (mm)	Revolution (min-1)	Table feed (mm/min)	Revolution (min-1)	Table feed (mm/min)	ap (mm)	ae (mm)
R 0.1	40000	320	40000	240	0.003	0.02	40000	320	40000	160	0.003	0.02	40000	320	40000	160	0.002	0.02
R 0.15	40000	640	40000	560	0.01	0.03	40000	640	40000	400	0.007	0.03	40000	640	40000	400	0.005	0.03
R 0.2	40000	1600	40000	1200	0.02	0.04	40000	1400	40000	1000	0.015	0.04	40000	1200	40000	1000	0.01	0.04
R 0.3	40000	3200	40000	1600	0.03	0.06	40000	2800	40000	1200	0.025	0.06	40000	2000	40000	1200	0.02	0.06
R 0.4	40000	6400	40000	2400	0.05	0.08	40000	4000	40000	1600	0.04	0.08	40000	2800	40000	1600	0.03	0.08
R 0.5	40000	8000	40000	3200	0.06	0.10	40000	5600	40000	2400	0.05	0.10	40000	3600	32000	1300	0.04	0.10
R 0.75	40000	9600	40000	4000	0.09	0.15	40000	7200	32000	2500	0.075	0.15	32000	4500	21000	1200	0.05	0.15
R 1	40000	9600	39000	4700	0.11	0.20	40000	8000	24000	2400	0.1	0.20	24000	3800	16000	1000	0.07	0.20
R 1.25	40000	10400	32000	4500	0.12	0.25	37000	8100	19000	2300	0.11	0.25	19000	3400	13000	1000	0.08	0.25
R 1.5	40000	12000	27000	4300	0.13	0.30	32000	7700	16000	2200	0.12	0.30	16000	3200	11000	880	0.09	0.30
R 2	32000	10880	20000	3600	0.15	0.40	24000	6200	12000	1900	0.13	0.40	12000	2400	8000	800	0.1	0.40
R 2.5	25000	9000	16000	2900	0.20	0.50	19000	5300	9600	1700	0.15	0.50	9600	2100	6000	600	0.1	0.50
R 3	21000	8400	13000	2600	0.25	0.60	16000	4800	8000	1600	0.2	0.60	8000	1700	5000	600	0.11	0.60
R 4	16000	6400	10000	2000	0.30	0.80	12000	3600	6000	1200	0.2	0.80	6000	1400	4000	480	0.11	0.80
R 5	13000	5200	8000	1700	0.50	1.00	10000	3200	4800	960	0.2	1.00	4800	1100	3000	420	0.12	1.00
R 6	9000	3600	6000	1300	050	120	7000	2200	3600	720	03	120	3600	860	2200	310	012	120
Depth of cut					.	.					.	. p					.	.

I

Note 1) If the rigidity of the machine or the work materials installation is very low, or chattering and noise are generated, reduce the revolution and feed rate proportionately. Note 2) If the depth of cut is shallow, the revolution and feed rate can be increased. Please reduce the feed rate when the surface finish is important. Note 3) % is the inclination angle of the machined surface. End mill

RE ap ae ae:Pick Feed

Общий каталог Mitsubishi 2020 - 2021 - страница 1006

Навигация

RECOMMENDED CUTTING CONDITIONS

I

Общий каталог Mitsubishi 2020 - 2021 - страница 1006

Навигация

RECOMMENDED CUTTING CONDITIONS

I

Отправьте заявку

На подбор необходимой оснастки и оборудования