Основной каталог Kyocera 2021 - 2022 - страница 865

Предыдущая страница Следующая страница

Навигация

Lead angle 0°/ 2° MFWN Spare parts Spare parts Wrench Anti-seize Clamp screw Shim Shim screw Wrench Mounting bolt compound Description TTW DTM MFWN 90063R-3T-M HH10X30 MFWN 90080R-4T-M SB-50140TR TTW-15 MFWN-90 SPW-7050 LW-5 HH12X35 Coarse pitch MFWN 90100R-5T-M - P-37 Recommended tightening torque for insert clamp Recommended tightening torque for shim clamp 4.2N•m 6.0N•m - ~ 90250R-12T-M MFWN 90063R-4T-M HH10X30 MFWN 90080R-5T-M SB-50140TR TTW-15 HH12X35 Fine pitch MFWN 90100R-7T-M Recommended tightening torque for insert clamp - - - - P-37 4.2N•m - ~ 90250R-14T-M MFWN 90063R-5T-M SB-50140TR TTW-15 - HH10X30 MFWN 90080R-7T-M SB-40140TRN - DTM-15 HH12X35 Extra fine pitch MFWN 90100R-9T-M - - - P-37 Recommended tightening torque for insert clamp - ~ 3.5N•m 90160R-14T-M Coat anti-seize compound thinly on portion of taper and thread when insert is fixed. How to mount an insert M 1. Be sure to remove dust and chips from the insert mounting pocket. 2. After applying anti-seize compound on portion of taper and thread, attach the screw to the front end of the wrench. While lightly pressing the insert against the constraint surfaces, put the screw into the hole of the insert and tighten. (Ref. to Fig. 1) 3. When tightening the screw, make sure that the wrench is parallel to the screw. Remember that the screw hole of the toolholder for Extra fine pitch is inclined to the bearing surface. (Ref. to Fig. 2 and Fig. 3) Milling 4. Be careful not to tighten the screw with excessive torque. Recommended tightening torque is 4.2N·m for M5 screw (SB-50140TR) and 3.5N·m for M4 screw (SB-40140TRN). 5. After tightening the screw, make sure that there is no clearance between the insert seat surface and the bearing surface of the toolholder or between the insert side surfaces and the constraint surface of the toolholder. If there is any clearance, remove the insert and mount it again according to the above steps. 6. To change the cutting edge of the insert, turn the insert counterclockwise (Ref. to Fig. 4). The insert corner identification number is stamped on the top surface of the insert. θ θ Fig. 1 Fig. 2 Fig. 3 Fig. 4 How to replace a shim (For coarse pitch) How to replace 1. Be sure to remove dustaand shim (forthecoarse chips from pitch) insert mounting pocket. 1. Be2.sure Thetoshim removemust beand dust mounted in the chips from theproper direction.pocket. insert mounting While aligning the surface of the shim with the mark on it to the corresponding constraint surface 2. The (Ref. shim to mustFig.be1)mounted in the and lightly proper the pressing direction. While aligning shim toward the surface the constraint of the (Ref. surface shim to with the Fig. 2),mark onthe insert it toscrew the corresponding into the holeconstraint of the shim and tighten (Ref. to surface (Ref. to Fig. 1) and lightly pressing the shim toward the constraint surface Fig. 3). When tightening the screw, make sure that the screw is vertical to the bearing surface (Recommended tightening torque is 6.0N·m). (Ref. to Fig. 2), insert the screw into the hole of the shim and tighten (Ref. to Fig. 3). When tightening the screw, make sure that the screw is vertical 3. After to the bearingtightening the screw, make surface (Recommended sure that tightening there torque is is no clearance between the shim seat surface and the bearing surface. If there is any clearance, 6.0N·m). 3. Afterremove tighteningthethe screw, insert andmake sureitthat mount there again is no clearance according to thebetween the shim seat surface and the bearing surface. If there is any clearance, above steps. remove the insert and mount it again according to the above steps. Shim Cutter body Shim screw Identifying Constraint surface Wrench mark Fig. 1 Fig. 2 Fig. 3 M93