Основной каталог Kyocera 2021 - 2022 - страница 40

Предыдущая страница Следующая страница

Навигация

Introduction Chipbreaker selection - Positive inserts Steel (Molded chipbreaker) B Name Design Advantages Name Design Advantages • 1st. 20° • Available for 0.05 recommendation Minute ap minute ap • Stable chip control CF (0.02 to 0.2 mm) 10° in a wide feed rate Finishing finishing range Turning indexable inserts PP •Stable tool life 5° due to special • Chipbreaker for edge design with 15° sharpness and Finishing finishing boring PF available from ap improved strength 0.15~0.6 mm 14° • Consistent Finishing chip breaking • Chips fragmented DP performance for Finishing 7.5° in small pieces in GF finishing machining of small ap 20° Finishing • Wide range of Finishing - Medium conditions by GP • Good chip control 5° using the optimum GQ chipbreaker width according to the cutting depth 13° • Sharp cutting • Good chip control Finishing performance due to for varied ap such 18° large rake angle VF as copying Finishing • Large dot to the and undercutting SK corner edge impro- 3° ved chip control in a wide feed rate range 0.2 13° 15° • Good cutting 5° Finishing - Medium performance • Applicable without • General purpose Finishing CK hand for two HQ chipbreaker for 20° 0.2 direction 15° medium machining machining on 5° automatic lathe • Wiper insert • Good surface finish 0.15 0° and good chip Finishing 10° WP control at high Medium 5° • Chipbreaker for feeds G 10° short chips • Reduces surface finish galling 0.1 Standard (without indication) 0.2 Finishing - Medium 17° • Good chip evacuation at wide Medium 6° • Strong edge GK range by breaker chipbreaker 0.1 dot and wide chip pocket 17° Applicable chipbreaker range (ap indicates radius) (Steel) (Stainless Steel) (Steel) (Steel) 2.0 5 (Steel) 5 4 1.5 4 4 CK 3 General purpose (Steel) 3 3 ap (mm) ap (mm) ap (mm) ap (mm) 3 1.0 GQ GF SK 2 ap (mm) 2 2 GK (07, 11) 2 Finishing 0.5 PF 1 GF 1 1 1 GF CF WP CF CF 0.15 0.2 0.05 0.1 0.15 0.2 0.05 0.1 0.15 0.2 0.05 0.1 0.15 0.2 0.1 0.2 0.3 0.4 0.5 0.1 0.2 0.3 0.4 rev) f (mm/rev) f (mm/rev) f (mm/rev) f (mm/rev) f (mm/rev) (Steel) (Steel / Edge Length = 11) 4 (Steel / Edge Length = 08, 09) 4 0.4 7KLVILOHLV (Steel / Edge Length = 11) 0.3 127FRQVLG 3 XP (not for epim only for editorial page in ) (Steel) 3 Standard 3 3 (GP) HUHGWREH XQ G ap (mm) ap (mm) 2 0.2 2 VF (16) 2 2 LQ(3,0 ap (mm) ap (mm) ap (mm) PP (11) VF (11) HQ HQ 1 0.1 CF 1 1 1 XP PP (07) (GP) (DP) GP 0.1 0.2 0.3 0.4 0.05 0.1 0.15 0.2 0.1 0.2 0.3 0.4 0.1 0.2 0.3 0.4 0.1 0.2 0.3 0.4 f (mm/rev) f (mm/rev) f (mm/rev) f (mm/rev) f (mm/rev) B12