Общий каталог Sumitomo 2019 - 2020 - страница 527

ISOISO cationClassicationClassi Workpiece HardnessWorkpiece Hardness (HB)(HB) ChipbreakerChipbreaker High-speedCast IronNon-ferrousMetalChamferingGroove /T-SlotR / 3DProfilingRadiusMulti-PurposeHigh FeedShoulderMillingFace MillingMillingCutters SEC-Wave Repeater WRX Type ■ Recommended Cutting Conditions Cutting Widthae=8mm WRX2000 Depth of Cut Tool: WRX2040E3642, Insert: AXMT123504PEER ap=30mm Cutting Conditions: Depth of Cut ap=30mm, Width of Cut ae=8mm, Dry Grade ACP100 ACP200 ACP300 ACK200 ACK300 ACM200 ACM300 DL1000 Work Material Feed Rate per Tooth fz (mm/t) 0.1 0.15 0.2 0.1 0.15 0.2 0.1 0.15 0.2 0.1 0.15 0.2 0.1 0.15 0.2 0.1 0.15 0.2 0.1 0.15 0.2 0.1 0.15 0.2 Cutting Speed vc (m/min) Steel, Carbon Steel S15C 125 G 280 260 240 260 240 220 240 220 200S45C190G200 180 160 180 160 140 180 160 140 H S45C Hardened 250 G 180 120 140 160 140 120 150 130 110 S75C 270 G 160 140 120 150 130 110 130 110 110 S75C Hardened 300 G 100 80 70 90 70 60 70 60 50 P Low Alloy Steel (SCM, SNCM) 180 G 200 180 160 180 160 150 160 150 130 SCM, SNCM Hardened 275 G 130 110 90 120 100 90 100 90 80 SCM, SNCM Hardened 300 G 120 100 80 100 90 80 90 80 60 SCM, SNCM Hardened 350 G 90 80 60 80 70 60 70 60 40 High-alloy Steel (SKD, SKT, SKH) 200 G 180 170 160 170 160 130 150 140 120 SKD, SKT, SKH Hardened 325 G 100 80 60 80 60 50 60 50 30 Stainless Steel SUS430 and Others (Martensitic / Ferritic) 200 E 170 150 120 140 130 110 M SUS403 and others (Martensitic / Hardened) 240 E 140 120 100 120 100 90 SUS304, SUS316 (Austenitic) 180 E 180 160 140 160 140 130 K Cast Iron G 240 220 200 220 200 180 Ductile Cast Iron G 160 140 120 140 120 100 S Exotic Alloy E 50 35 45 25 N For Aluminum Alloy Si <12.6%Si >12.6% SS 1000 750 500250 200 170 ● The recommended cutting conditions may not be practical depending on the operating conditions (e.g. machine, workpiece shape, clamping system). Note The cutting conditions above are a guide. Actual conditions will need to be adjusted according to machine rigidity, work clamp rigidity, depth of cut and other factors. Cutting Width ｍｍ WRX3000 Depth of Cut Tool: WRX3050E5342 Insert: AXMT170508PEER ｍｍ Cutting Conditions: Depth of Cut ap=50mm, Width of Cut ae=10mm, Dry Grade ACP100 ACP200 ACP300 ACK200 ACK300 ACM200 ACM300 DL1000 Work Material Feed Rate per Tooth fz (mm/t) 0.1 0.15 0.2 0.1 0.15 0.2 0.1 0.15 0.2 0.1 0.15 0.2 0.1 0.15 0.2 0.1 0.15 0.2 0.1 0.15 0.2 0.1 0.15 0.2 Cutting Speed vc (m/min) Steel, Carbon Steel S15C 125 G 320 300 280 300 280 260 280 260 240 S45C 190 G 240 220 200 220 200 180 200 180 160 S45C Hardened 250 G 200 180 160 180 160 140 160 140 120 S75C 270 G 160 140 120 150 130 110 130 110 110 S75C Hardened 300 G 120 100 80 100 80 60 80 60 50 P Low Alloy Steel (SCM, SNCM) 180 G 220 200 180 200 180 170 180 170 150 SCM, SNCM Hardened 275 G 140 120 100 130 110 100 110 100 80 SCM, SNCM Hardened 300 G 130 110 90 110 90 80 100 80 60 SCM, SNCM Hardened 350 G 100 80 60 90 70 60 70 60 40 High-alloy Steel (SKD, SKT, SKH) 200 G 200 180 160 180 160 140 160 140 120 SKD, SKT, SKH Hardened 325 G 100 80 60 80 60 50 60 50 30 Stainless Steel SUS430 and Others (Martensitic / Ferritic) 200 E 170 150 130 140 130 110 M SUS403 and others (Martensitic / Hardened) 240 E 140 120 100 120 100 90 SUS304, SUS316 (Austenitic) 180 E 180 160 140 160 140 130 K Cast Iron G 240 220 200 220 200 180 Ductile Cast Iron G 160 140 120 140 120 100 S Exotic Alloy E 50 30 45 25 N For Aluminum Alloy Si <12.6% S 1000 750 500 Si >12.6% S 250 200 170 ● The recommended cutting conditions may not be practical depending on the operating conditions (e.g. machine, workpiece shape, clamping system). Note The cutting conditions above are a guide. Actual conditions will need to be adjusted according to machine rigidity, work clamp rigidity, depth of cut and other factors. H83