Общий каталог SGS 2021 - страница 45

METRIC Z-Carb-AP 38° 35° 4 ≠ ≠ LF APMX DC DCON RE Z1MPCRMETRIC SERIES TOLERANCES (mm) mm EDP NO. • Variable rake geometry CUTTING LENGTH OVERALL SHANK CORNER Ti-NAMITE-X Ti-NAMITE-X JetStream <3 DIAMETER DIAMETER OF CUT LENGTH DIAMETER RADIUS W/FLAT alters and controls the DC = +0,012/–0,012 DC APMX LF DCON RE cutting dynamic taking chatter suppression to DCON = h 6 1,0 3,0 57,0 6,0 0,1 46873* – – an unprecedented level RE = +0,000/–0,025 1,5 4,5 57,0 6,0 0,1 46849* – – • Unequal helix design 3–6 DIAMETER 2,0 6,0 57,0 6,0 0,2 46850* – – changes the cutting 2,5 7,0 57,0 6,0 0,2 46874* – – angle to improve DC = +0,000/–0,030 harmonics DCON = h 6 3,0 8,0 57,0 6,0 0,3 46851 – – • Unequal flute spacing RE = +0,000/–0,050 3,0 8,0 57,0 6,0 0,5 46880 – – helps to disrupt the 4,0 11,0 57,0 6,0 0,3 46852 – – rhythmic pattern >6–10 DIAMETER 4,0 11,0 57,0 6,0 0,5 46881 – – created by the cutting DC = +0,000/–0,040 edge helping to 5,0 13,0 57,0 6,0 0,3 46853 – – suppress damaging DCON = h 6 6,0 13,0 57,0 6,0 0,25 46882 – – harmonics RE = +0,000/–0,050 6,0 13,0 57,0 6,0 0,5 46854 – – • Enhanced corner >10–25 DIAMETER 6,0 13,0 57,0 6,0 1,0 46855 – – geometry with tight tolerance corner radii DC = +0,000/–0,050 6,0 13,0 57,0 6,0 1,5 46884 – – • Recommended for DCON = h 6 8,0 19,0 63,0 8,0 0,5 46856 – – materials ≤ 45 HRc RE = +0,000/–0,050 8,0 19,0 63,0 8,0 1,0 46857 – – (≤ 420 Bhn) 8,0 19,0 63,0 8,0 1,5 46886 – – STEELS 8,0 19,0 63,0 8,0 2,0 46887 – – 10,0 22,0 72,0 10,0 0,5 46858 – – STAINLESS STEELS 10,0 22,0 72,0 10,0 1,0 46859 – – CAST IRON 10,0 22,0 72,0 10,0 1,5 46889 – – 10,0 22,0 72,0 10,0 2,0 46890 – – HIGH TEMP ALLOYS 10,0 22,0 72,0 10,0 2,5 46891 – – TITANIUM 12,0 26,0 83,0 12,0 0,5 46860 46909 – 12,0 26,0 83,0 12,0 0,75 46861 46910 46493 12,0 26,0 83,0 12,0 1,0 46893 46911 – For patent 12,0 26,0 83,0 12,0 1,5 46894 46912 – information visit 12,0 26,0 83,0 12,0 2,0 46895 46913 – www.ksptpatents.com 12,0 26,0 83,0 12,0 2,5 46896 46914 – 12,0 26,0 83,0 12,0 3,0 42718 46915 42719 14,0 26,0 83,0 14,0 1,0 46862 46916 46494 16,0 32,0 92,0 16,0 1,0 46863 46917 46495 16,0 32,0 92,0 16,0 1,5 46898 46918 – 16,0 32,0 92,0 16,0 2,0 46899 46919 – 16,0 32,0 92,0 16,0 2,5 46900 46920 – 16,0 32,0 92,0 16,0 3,0 46864 46921 42721 16,0 32,0 92,0 16,0 4,0 46867 46944 – 20,0 38,0 104,0 20,0 1,0 46865 46922 46497 20,0 38,0 104,0 20,0 1,5 46903 46923 – 20,0 38,0 104,0 20,0 2,0 46904 46924 – 20,0 38,0 104,0 20,0 2,5 46905 46925 – 20,0 38,0 104,0 20,0 3,0 42722 46926 42723 20,0 38,0 104,0 20,0 4,0 46868 46945 – 20,0 38,0 104,0 20,0 5,0 46869 46946 – 25,0 38,0 104,0 25,0 1,0 46866 46927 46498 *Variable flute spacing. Helix and rake do not vary. 45 END MILLS www.kyocera-sgstool.com END MILLS