Общий каталог SGS 2018 - страница 55
Навигация
Каталог SGS шестизубые фрезы T-carb
Каталог SGS микро инструмент 2021
Каталог SGS фрезы для алюминия S-carb
Каталог SGS высокопроизводительные черновые фрезы
Каталог SGS инструмент для обработки алюминия
Общий каталог SGS 2015 на русском
| Series ZH1CR | Ae | Ap Ae | Vc | Diameter (D1 (inch) | ) | |||||
| Fractional | Hardness | Ae x D1 | Ap x D1 | (sfm) | 1/4 | 3/8 | 1/2 | 3/4 | 1 | |
| Profile | 85 | RPM | 1299 | 866 | 649 | 433 | 325 | |||
| SUPER ALLOYS | ≤ 0.5 | ≤ 1.5 | (68102) | Fz | 0.0007 | 0.0012 | 0.0017 | 0.0020 | 0.0023 | |
| (NICKEL, COBALT, IRON BASE) | ≤ 300 Bhn | - | Feed(ipm) | 3.6 | 4.2 | 4.4 | 3.5 | 3.0 | ||
| Inconel 601, 617, 625, | or ≤ 32 HRc Slot | 70 | RPM | 1070 | 713 | 535 | 357 | 267 | ||
| Incoloy, Monel 400 | 1 | ≤ 1 | (56-84) | Fz | 0.0007 | 0.0012 | 0.0017 | 0.0020 | 0.0023 | |
| Feed(ipm) | 3.0 | 3.4 | 3.6 | 2.9 | 2.5 | |||||
| SUPER ALLOYS | Profile | 70 | RPM | 1070 | 713 | 535 | 357 | 267 | ||
| (NICKEL, COBALT, | ≤ 0.5 | ≤ 1.5 | (5684) | Fz | 0.0005 | 0.0009 | 0.0012 | 0.0014 | 0.0016 | |
| IRON BASE) | ≤ 400 Bhn | - | Feed(ipm) | 2.1 | 2.6 | 2.6 | 2.0 | 1.7 | ||
| Inconel 718, X-750, | or ≤ 43 HRc Slot | 55 | RPM | 840 | 560 | 420 | 280 | 210 | ||
| Incoloy, Waspaloy, | 1 | ≤ 1 | (44-66) | Fz | 0.0005 | 0.0009 | 0.0012 | 0.0014 | 0.0016 | |
| S Hastelloy, Rene | Feed(ipm) | 1.7 | 2.0 | 2.0 | 1.6 | 1.3 | ||||
| Profile | 215 | RPM | 3285 | 2190 | 1643 | 1095 | 821 | |||
| TITANIUM ALLOYS | ≤ 0.5 | ≤ 1.5 | (172-258) | Fz | 0.0008 | 0.0015 | 0.0020 | 0.0024 | 0.0028 | |
| Pure Titanium, Ti6Al4V, | ≤ 350 Bhn | Feed(ipm) | 10.5 | 13.1 | 13.1 | 10.5 | 9.2 | |||
| Ti6Al2Sn4Zr2Mo, | or ≤ 38 HRc Slot | 170 | RPM | 2598 | 1732 | 1299 | 866 | 649 | ||
| Ti4Al4Mo2Sn0.5Si | 1 | ≤ 1 | (136204) | Fz | 0.0008 | 0.0015 | 0.0020 | 0.0024 | 0.0028 | |
| - | Feed(ipm) | 8.3 | 10.4 | 10.4 | 8.3 | 7.3 | ||||
| TITANIUM ALLOYS | Profile | 75 | RPM | 1146 | 764 | 573 | 382 | 287 | ||
| (DIFFICULT) | ≤ 0.5 | ≤ 1.5 | 6090 | Fz | 0.0008 | 0.0015 | 0.0020 | 0.0024 | 0.0028 | |
| Ti10Al2Fe3Al, | ≤ 440 Bhn | (-) | Feed(ipm) | 3.7 | 4.6 | 4.6 | 3.7 | 3.2 | ||
| Ti5Al5V5Mo3Cr, Ti7Al4Mo, Ti3Al8V6Cr4Zr4Mo | or ≤ 47 HRc Slot | 60 | RPM | 917 | 611 | 458 | 306 | 229 | ||
| , Ti6Al6V6Sn, Ti15V3 | 1 | ≤ 1 | (48-72) | Fz | 0.0008 | 0.0015 | 0.0020 | 0.0024 | 0.0028 | |
| Cr3Sn3Al | Feed(ipm) | 2.9 | 3.7 | 3.7 | 2.9 | 2.6 |
Bhn (Brinell) HRc (Rockwell C) rpm = Vc x 3.82 / D 1 ipm = Fz x 4 x rpm HIGH TEMP ALLOYS reduce speed and feed for materials harder than listed reduce feed and Ae when finish milling (.02 x D maximum) TITANIUM 1 refer to the KYOCERA SGS Tool Wizard® for complete technical information (www.kyocera-sgstool.com)