Каталог Iscar токарный инструмент 2017 - страница 115
Навигация
Каталог Iscar резьбонарезные фрезы
Каталог Iscar инструмент для обработки алюминиевых колёс
Каталог Iscar державки и пластины для нарезания резьбы 2022
Каталог Iscar расточные системы 2022
Каталог Iscar высокоточные развертки и метчики 2022
Токарные инструменты Iscar (часть 2) 2026
ISOTURN INSERTS
80°
95° 95º
WNMG-M3P l 95°
Double-Sided Trigon Inserts for
Medium Machining Conditions on Steel
r
di S
Recommended
Dimensions Tough 1 Hard
Machining Data
IC8350
IC8250
IC8150
IC5010
IC807
ap f
Designation l di S r (mm) (mm/rev)
WNMG 06T304-M3P 6.52 9.52 3.97 0.40 • • 0.45-2.50 0.10-0.45
WNMG 06T308-M3P 6.52 9.52 3.97 0.80 • • • 0.50-3.00 0.15-0.50
WNMG 06T312-M3P 6.52 9.52 3.97 1.20 • 0.80-3.00 0.18-0.60
WNMG 060404-M3P 6.52 9.52 4.76 0.40 • • • 0.45-2.50 0.10-0.45
WNMG 060408-M3P 6.52 9.52 4.76 0.80 • • • 0.50-3.00 0.15-0.50
WNMG 060412-M3P 6.52 9.52 4.76 1.20 • • 0.80-3.00 0.18-0.60
WNMG 080404-M3P 8.70 12.70 4.76 0.40 • • • 0.40-3.50 0.10-0.45
WNMG 080408-M3P 8.70 12.70 4.76 0.80 • • • • 0.50-4.00 0.15-0.50
WNMG 080412-M3P 8.70 12.70 4.76 1.20 • • • • 0.80-4.00 0.18-0.60
WNMG 080416-M3P 8.70 12.70 4.76 1.60 • • 1.00-4.00 0.23-0.65
• For user guide and cutting speed recommendations, see pages 197-212
For tools, see pages: A-PWLNR/L-X/G (84) • A/S-MWLNR/L-W (83) • A/S-PWLNR/L (84) • C#-MULNR/L-MW (19) • C#-PWLNR/L-08-JHP (13) •
C#-PWLNR/L-X (16) • C#-PWLNR/L-X-JHP (17) • DWLNR/L (13) • E-PWLNR/L-HEAD (85) • HSK A63WH-MULNR-J12MWX2 (20) • HSK A63WH-MULNR/L-MW
(19) • HSK A63WH-MUMNN-MW (20) • MULNR/L-12MW (18) • MWLNR/L-CA-W (101) • MWLNR/L-W (21) • PWLNR/L (12) • PWLNR/L-08-JHP (13) •
PWLNR/L-X (14) • PWLNR/L-X-JHP (15) • PWLNR/L-X-JHP-MC (16) • S-DWLNR/L (78) • S-MULNR-MW (85)
80°
95°
l 18°
95°
WOMG-10-T3P-IQ
Double-Sided 6° Negative r
Side Flank Trigon Inserts for di S
High Feed Turning of Steel
Recommended
Dimensions Tough 1 Hard
Machining Data
IC8350
IC8250
IC8150
ap f
Designation l di S r (mm) (mm/rev)
WOMG 100716-T3P-IQ 10.86 15.88 7.94 1.60 • • • 1.00-2.80 1.50-3.00
• The specified machining recommendations in the above table are valid only for PWXOR/L-TF-IQ tools. For PWLOR/L-IQ tools: ap= 3-7 mm, ft= 0.3-0.8 mm/rev.
• For user guide, see pages 197-212
For tools, see pages: PWLOR/L-IQ (22) • PWXOR/L-TF-IQ (23)
Application Range on PWXOR/L-TF-IQ Tools
ap
mm
3.5
3.0
2.5
2.0
1.5
1.0
0.5
0.5 1.0 1.5 2.0 2.5 3.0 3.5 F (mm/rev)
111
80°
95° 95º
WNMG-M3P l 95°
Double-Sided Trigon Inserts for
Medium Machining Conditions on Steel
r
di S
Recommended
Dimensions Tough 1 Hard
Machining Data
IC8350
IC8250
IC8150
IC5010
IC807
ap f
Designation l di S r (mm) (mm/rev)
WNMG 06T304-M3P 6.52 9.52 3.97 0.40 • • 0.45-2.50 0.10-0.45
WNMG 06T308-M3P 6.52 9.52 3.97 0.80 • • • 0.50-3.00 0.15-0.50
WNMG 06T312-M3P 6.52 9.52 3.97 1.20 • 0.80-3.00 0.18-0.60
WNMG 060404-M3P 6.52 9.52 4.76 0.40 • • • 0.45-2.50 0.10-0.45
WNMG 060408-M3P 6.52 9.52 4.76 0.80 • • • 0.50-3.00 0.15-0.50
WNMG 060412-M3P 6.52 9.52 4.76 1.20 • • 0.80-3.00 0.18-0.60
WNMG 080404-M3P 8.70 12.70 4.76 0.40 • • • 0.40-3.50 0.10-0.45
WNMG 080408-M3P 8.70 12.70 4.76 0.80 • • • • 0.50-4.00 0.15-0.50
WNMG 080412-M3P 8.70 12.70 4.76 1.20 • • • • 0.80-4.00 0.18-0.60
WNMG 080416-M3P 8.70 12.70 4.76 1.60 • • 1.00-4.00 0.23-0.65
• For user guide and cutting speed recommendations, see pages 197-212
For tools, see pages: A-PWLNR/L-X/G (84) • A/S-MWLNR/L-W (83) • A/S-PWLNR/L (84) • C#-MULNR/L-MW (19) • C#-PWLNR/L-08-JHP (13) •
C#-PWLNR/L-X (16) • C#-PWLNR/L-X-JHP (17) • DWLNR/L (13) • E-PWLNR/L-HEAD (85) • HSK A63WH-MULNR-J12MWX2 (20) • HSK A63WH-MULNR/L-MW
(19) • HSK A63WH-MUMNN-MW (20) • MULNR/L-12MW (18) • MWLNR/L-CA-W (101) • MWLNR/L-W (21) • PWLNR/L (12) • PWLNR/L-08-JHP (13) •
PWLNR/L-X (14) • PWLNR/L-X-JHP (15) • PWLNR/L-X-JHP-MC (16) • S-DWLNR/L (78) • S-MULNR-MW (85)
80°
95°
l 18°
95°
WOMG-10-T3P-IQ
Double-Sided 6° Negative r
Side Flank Trigon Inserts for di S
High Feed Turning of Steel
Recommended
Dimensions Tough 1 Hard
Machining Data
IC8350
IC8250
IC8150
ap f
Designation l di S r (mm) (mm/rev)
WOMG 100716-T3P-IQ 10.86 15.88 7.94 1.60 • • • 1.00-2.80 1.50-3.00
• The specified machining recommendations in the above table are valid only for PWXOR/L-TF-IQ tools. For PWLOR/L-IQ tools: ap= 3-7 mm, ft= 0.3-0.8 mm/rev.
• For user guide, see pages 197-212
For tools, see pages: PWLOR/L-IQ (22) • PWXOR/L-TF-IQ (23)
Application Range on PWXOR/L-TF-IQ Tools
ap
mm
3.5
3.0
2.5
2.0
1.5
1.0
0.5
0.5 1.0 1.5 2.0 2.5 3.0 3.5 F (mm/rev)
111