Каталог Iscar отрезка 2022 - страница 121

Предыдущая страница Следующая страница

Навигация

GHFG-R/L-8 Holders for Face GroovingDAXHF N-DAXXLHH
and Turning Along ShaftsCDXCW WFOALGHFG-25- B50R-8
Right-handshown
DesignationCDXDAXN(1)DAXX(2)HHFBOALLHWF
GHFG 25-50R/L-825.0050.064.025.025.025.0150.0041.022.00SR M6X20 DIN912HW 5.0
GHFG 25-63R/L-825.0063.082.025.025.025.0150.0041.022.00SR M6X20 DIN912HW 5.0
GHFG 32-63R-825.0063.082.032.032.032.0170.0041.030.00SR M6X20 DIN912HW 5.0

Dimensions Tough 1 Hard Recommended Machining Data

p

DesignationCWRE CWTOL(1)RETOL(2)INSL BW(mm)(mm/rev)(mm/rev)(mm/rev)(mm/rev)• For user guide, see pages 604-613
GRIP 3015Y3.001.500.050.05015.802.10• • • • • • • • • •0.00-1.500.18-0.260.07-0.130.08-0.200.10-0.20(1) Minimum penetration diameter
GRIP 318-159Y• • •(2) Maximum penetration diameter
3.181.590.050.05015.802.300.00-1.500.19-0.280.07-0.130.08-0.200.10-0.20
GRIP 4020Y• • • • • • • • • •For inserts, see pages: GDMF (288) • GDMM-CC (583) • GDMN (289) • GDMU (290) • GDMY (289) • GDMY (full radius) (291) • GDMY-F (291)
4.002.000.050.05019.002.800.00-2.000.20-0.340.09-0.170.10-0.240.15-0.30
  • GIA-K (long pocket) (299)
  • GIF (long pocket) (298)
  • GIF-E (W=8,10 full radius) (294)
  • GIF-E (W=8,10) (292)
  • GIFG-E (W=8) (581)
GRIP 476-238Y4.762.380.050.05019.003.200.00-2.300.21-0.400.10-0.200.10-0.240.15-0.30
GRIP 5025Y5.002.500.050.05019.003.40• •• • •• • •0.00-2.500.23-0.420.11-0.210.12-0.240.15-0.35
GRIP 6030Y6.003.000.050.05019.004.20• • • • • • • • •0.00-3.000.24-0.500.13-0.250.12-0.280.15-0.40
GRIP 635-318Y6.353.180.050.05019.004.00• ••0.00-3.100.25-0.530.14-0.270.12-0.280.15-0.40
  • For cutting speed recommendations and user guide, see pages 604-613
GHFGR/L-8CDX HLH FH
Holders for Face Grooving and TurningDAXN-DAXX WFCWOAL HBHBRight-handshown
DesignationCDXDAXN(1)DAXX(2)HHFBOALLHWFHBH
GHFGR/L 25-80-823.0080.0115.025.025.025.0150.0043.521.306.0SR M6X20 DIN912HW 5.0
GHFGR/L 32-80-823.0080.0115.032.032.032.0170.0043.528.30-SR M6X20 DIN912HW 5.0
GHFGR/L 25-105-825.00105.0160.025.025.025.0150.0043.521.306.0SR M6X20 DIN912HW 5.0
GHFGR/L 32-105-825.00105.0160.032.032.032.0170.0043.528.30-SR M6X20 DIN912HW 5.0
GHFGR/L 25-155-825.00155.0510.025.025.025.0150.0043.521.306.0SR M6X20 DIN912HW 5.0
GHFGR/L 32-155-825.00155.0510.032.032.032.0170.0043.528.30-SR M6X20 DIN912HW 5.0
  • HFPAD-3 (562)
  • HFPAD-4 (563)
  • HFPAD-5 (563)
  • HFPAD-6 (564)
  • HFPAD-JHP (562)
  • HGAER/L-3 (565)
  • HGAIR/L-3 (568)
  • HGFH (268)
  • No limitation to widening the groove either way after initial grooving
  • CDX depends on the penetration diameter and the insert
  • For user guide, see pages 604-613

(1) Minimum penetration diameter (2) Maximum penetration diameter

For inserts, see pages: GDMF (288) GDMM-CC (583) GDMN (289) GDMU (290) GDMY (289) GDMY (full radius) (291) GDMY-F (291)

  • GIA-K (long pocket) (299)
  • GIF (long pocket) (298)
  • GIF-E (W=8,10 full radius) (294)
  • GIF-E (W=8,10) (292)
  • GIFG-E (W=8) (581)
  • GIPA/GIDA 8 (full radius) (302)
CDX for GHFGR/L(25/32)-80-8
DGIF 8…GIFG 8…GDMY 8…GIPA 8…GIDA 8…GIA 8…GDMM 8CC…
8016232320241624
8217232320241724
8418232321241824
8619232321241924
8820232322242024
9020232322242024
9620232322242024
10420232322242024
11522232322242224
CDX for GHFGR/L(25/32)-105-8
DGIF 8…GIFG 8…GDMY 8…GIPA 8…GIDA 8…GIA 8…GDMM 8CC…
10521232323242124
11422232323242224
12623232423242324
140-16024242423242424
CDX for GHFGR/L(25/32)-155-8
DGIF 8…GIFG 8…GDMY 8…GIPA 8…GIDA 8…GIA 8…GDMM 8CC…
15524242423242424
18024242423242424
210-51024242423242424