Каталог Iscar отрезка 2022 - страница 118

FACE GROOVING
±0.1
HFPR/L 19 Ref. CW
Utility Double-Ended Face
Machining Inserts DAXN-DAXX 7°

RE BW
No depth penetration limit

Dimensions Tough 1 Hard Recommended Machining Data

f face-
ap groove f face-turn


IC8250

IC9015

IC5010
IC830
IC354

IC808


IC806
IC20
Designation CW RE CWTOL(1) RETOL(2) BW DAXN(3) DAXX(4) (mm) (mm/rev) (mm/rev)
HFPR/L 3003 3.00 0.30 0.05 0.050 2.10 25.6 51.5 • • • • • • • 0.30-1.50 0.08-0.20 0.10-0.20
HFPR/L 4004 4.00 0.40 0.05 0.050 2.80 24.1 73.7 • • • • • • • 0.40-2.00 0.10-0.24 0.15-0.25
HFPR/L 5004 5.00 0.40 0.05 0.050 3.40 22.1 170.0 • • • • • • • • 0.50-2.50 0.12-0.24 0.15-0.35
HFPR/L 6004 6.00 0.40 0.05 0.050 4.00 20.8 - • • • • • • • 0.40-3.00 0.12-0.28 0.15-0.40
• For cutting speed recommendations and user guide, see pages 604-613
(1) Cutting width tolerance (+/-)
(2) Corner radius tolerance (+/-)
(3) Minimum axial grooving diameter-applies to type M tools only. For other tools, apply the diameter limitations that are recorded on each tool.
(4) Maximum axial grooving diameter-applies to type M tools only. For other tools, apply the diameter limitations that are recorded on each tool.
For tools, see pages: C#-HFIR/L-MC (573) • CR HFIR-M (575) • HFAER/L-4 (565) • HFAER/L-5T, 6T (566) • HFAIR/L-4 (572) • HFAIR/L-DG (573)
• HFFR/L-T (564) • HFHPR/L-M (566) • HFHR/L-3T (558) • HFHR/L-4T (559) • HFHR/L-5T (560) • HFHR/L-6T (561) • HFHR/L-M (566)
• HFIR/L-MC (574) • HFPAD-4 (563) • HFPAD-5 (563) • HFPAD-6 (564) • HFPAD-JHP (562) • IM-HFIR-MC (574)


±0.1
HFPR/L (full radius) 19 Ref. CW
Utility Double-Ended Full Radius
Face Machining Inserts DAXN-DAXX 7°

RE BW
No depth penetration limit.

Dimensions Tough 1 Hard Recommended Machining Data

ap f face-groove f face-turn
IC8250

IC9015

IC5010
IC830
IC354

IC808


IC806
IC20


Designation CW RE CWTOL(1) RETOL(2) BW DAXN(3) DAXX(4) (mm) (mm/rev) (mm/rev)
HFPR/L 3015 3.00 1.50 0.05 0.050 2.10 25.6 51.5 • • • • • • • 0.00-1.50 0.08-0.20 0.12-0.20
HFPR/L 4020 4.00 2.00 0.05 0.050 2.80 24.1 73.7 • • • • • • • 0.00-2.00 0.10-0.24 0.15-0.25
HFPL 5025 5.00 2.50 0.05 0.050 3.40 22.1 170.0 • • • • • • • 0.00-2.50 0.12-0.24 0.15-0.35
HFPR 5025 5.00 2.50 0.05 0.050 3.40 22.1 170.0 • • • • • • • 0.00-2.50 0.12-0.24 0.15-0.35
HFPR/L 6030 6.00 3.00 0.05 0.050 4.00 20.8 - • • • • • • • 0.00-3.00 0.12-0.28 0.20-0.40
• For cutting speed recommendations and user guide, see pages 604-613
(1) Cutting width tolerance (+/-)
(2) Corner radius tolerance (+/-)
(3) Minimum axial grooving diameter-applies to type M tools only. For other tools, apply the diameter limitations that are recorded on each tool.
(4) Maximum axial grooving diameter-applies to type M tools only. For other tools, apply the diameter limitations that are recorded on each tool.
For tools, see pages: C#-HFIR/L-MC (573) • CR HFIR-M (575) • HFAER/L-4 (565) • HFAER/L-5T, 6T (566) • HFAIR/L-4 (572) • HFAIR/L-DG (573)
• HFFR/L-T (564) • HFHPR/L-M (566) • HFHR/L-3T (558) • HFHR/L-4T (559) • HFHR/L-5T (560) • HFHR/L-6T (561) • HFHR/L-M (566)
• HFIR/L-MC (574) • HFPAD-4 (563) • HFPAD-5 (563) • HFPAD-6 (564) • HFPAD-JHP (562) • IM-HFIR-MC (574)


576 ISCAR