Каталог Iscar отрезка 2022 - страница 100

Предыдущая страница Следующая страница

Навигация

HGHR/L-3LHHOAH
Integral Holders for Face Grooving and TurningCDXDAXN-DAXXCDX WF CWHBH OALBOAWRight-handshown
DesignationHBCWCDXHBHWFDAXN(1)DAXX(2)OALLHOAHOAW
HGHR 1010-12-3T610.010.03.006.002.09.5012.016.0120.0019.019.013.70SR 76-1400T-20/3
HGHR 1010-16-3T610.010.03.006.002.09.5016.025.0120.0019.019.012.80SR 76-1400T-20/3
HGHR/L 1212-12-3T612.012.03.006.00-11.0012.016.0120.0019.019.015.70SR 76-1400T-20/3
HGHR 1212-16-3T612.012.03.006.00-11.0016.025.0120.0019.019.014.80SR 76-1400T-20/3
HGHR/L 1616-12-3T616.016.03.006.00-15.0012.016.0120.0019.021.019.70SR 76-1400T-20/3
HGHR/L 1616-16-3T616.016.03.006.00-15.0016.025.0120.0019.021.018.80SR 76-1400T-20/3
HGHR/L 2020-12-3T620.020.03.006.00-20.0012.016.0120.0019.025.024.00SR 76-1400T-20/3
HGHR/L 2020-16-3T620.020.03.006.00-20.0016.025.0120.0019.025.024.00SR 76-1400T-20/3
HGHR/L 2525-12-3T625.025.03.006.00-25.0012.016.0120.0019.030.029.00SR 76-1400T-20/3
HGHR/L 2525-16-3T625.025.03.006.00-25.0016.025.0120.0019.030.029.00SR 76-1400T-20/3
  • HGN & GRIP inserts can be used only with right-hand toolholders, HGPL inserts only with left-hand toolholders
  • For user guide, see pages 604-613

(1) Minimum penetration diameter (2) Maximum penetration diameter

For inserts, see pages: GRIP (269) GRIP (full radius) (270) HGN-C (489) HGN-J (489) HGN-UT (490) HGPL (578)

No limitation for widening groove toward or away

from center, except for the following tools:dHGHR/L...-12-3T6
Dd
12.04.0
Limitation of widening toward center
13.01.0

depends on the major diameter (D) 13.5 0

D as per chart.

HFHR/L-3T Integral Holders for FacingWF2 CDX DAXN-DAXX CDX HFHR/L--3T12WF CW LH HFH B OAH
OALRight-hand shown
DesignationCWCDXHHFBOALWFWF2DAXN(2)DAXX(3)LHOAH
HFHR/L 20-25-3T123.0012.0020.020.020.0140.0020.505.325.030.038.028.0SR M6X16 DIN912HW 5.0
HFHR/L 20-30-3T123.0012.0020.020.020.0140.0020.505.330.038.038.029.0SR M6X16 DIN912HW 5.0
HFHR/L 20-38-3T123.0012.0020.020.020.0140.0020.505.338.048.038.030.0SR M6X16 DIN912HW 5.0
HFHR/L 20-48-3T123.0012.0020.020.020.0140.0020.505.348.060.038.030.0SR M6X16 DIN912HW 5.0
HFHR/L 25-25-3T123.0012.0025.025.025.0150.0025.505.325.030.038.033.0SR M6X16 DIN912HW 5.0
HFHR/L 25-30-3T123.0012.0025.025.025.0150.0025.505.330.038.038.034.0SR M6X16 DIN912HW 5.0
HFHR/L 25-38-3T123.0012.0025.025.025.0150.0025.505.338.048.038.035.0SR M6X16 DIN912HW 5.0
HFHR/L 20-60-3T22(1)3.0022.0020.020.020.0140.0020.50-60.075.040.031.0SR M6X16 DIN912HW 5.0
HFHR/L 25-48-3T22(1)3.0022.0025.025.025.0150.0025.50-48.060.040.036.0SR M6X16 DIN912HW 5.0
HFHR/L 25-60-3T22(1)3.0022.0025.025.025.0150.0025.50-60.075.040.036.0SR M6X16 DIN912HW 5.0
HFHR/L 20-75-3T25(1)3.0025.0020.020.020.0140.0020.50-75.0100.043.031.0SR M6X16 DIN912HW 5.0
HFHR/L 25-75-3T25(1)3.0025.0025.025.025.0150.0025.50-75.0100.043.036.0SR M6X16 DIN912HW 5.0
  • For user guide, see pages 604-613

(1) For deep face grooving only. (2) Minimum penetration diameter (3) Maximum penetration diameter

For inserts, see pages: HFPR/L (576) HFPR/L (full radius) (576)

No limitation for widening groove toward or away

from center, except for the following tools:d
HFHR/L-:-25-3T12HFHR/L-:-25-4T12HFHR/L-:-29-4T12Limitation of
D dD dD dwidening toward
25 525 129 1D center (d) depends on the major
26 2≥26 0≥46 0diameter (D) as
≥27 0per chart.