Каталог Iscar обработка канавок 2022 - страница 16

GROOVE-TURN INSL (Ref.) GRIP (full radius) ±0.1 Utility Double-Ended Full 7° Radius Inserts for External, Internal and Face Machining CW RE BW No depth penetration limit Dimensions Tough 1 Hard Recommended Machining Data f face- f face- IC8250 IC5010 ap f turn f groove groove turn IC830 IC808 IC908 IC418 IC806 IC807 IC804 IC08 Designation CW RE CWTOL(1) RETOL(2) INSL BW (mm) (mm/rev) (mm/rev) (mm/rev) (mm/rev) GRIP 3015Y 3.00 1.50 0.05 0.050 15.80 2.10 • • • • • • • • • • 0.00-1.50 0.18-0.26 0.07-0.13 0.08-0.20 0.10-0.20 GRIP 318-159Y 3.18 1.59 0.05 0.050 15.80 2.30 • • • 0.00-1.50 0.19-0.28 0.07-0.13 0.08-0.20 0.10-0.20 GRIP 4020Y 4.00 2.00 0.05 0.050 19.00 2.80 • • • • • • • • • • 0.00-2.00 0.20-0.34 0.09-0.17 0.10-0.24 0.15-0.30 GRIP 476-238Y 4.76 2.38 0.05 0.050 19.00 3.20 • • • • 0.00-2.30 0.21-0.40 0.10-0.20 0.10-0.24 0.15-0.30 GRIP 5025Y 5.00 2.50 0.05 0.050 19.00 3.40 • • • • • • • • 0.00-2.50 0.23-0.42 0.11-0.21 0.12-0.24 0.15-0.35 GRIP 6030Y 6.00 3.00 0.05 0.050 19.00 4.20 • • • • • • • • • 0.00-3.00 0.24-0.50 0.13-0.25 0.12-0.28 0.15-0.40 GRIP 635-318Y 6.35 3.18 0.05 0.050 19.00 4.00 • • • 0.00-3.10 0.25-0.53 0.14-0.27 0.12-0.28 0.15-0.40 • For cutting speed recommendations and user guide, see pages 419-428, 432-436 (1) Cutting width tolerance (+/-) (2) Corner radius tolerance (+/-) For tools, see pages: C#-HELIR/L (265) • C#-HFIR/L-MC (573) • CR HFIR-M (575) • D/HGAD RE/LE-JHP (499) • DGAD/HGAD (479) • DGFH (268) • DGFH-JHP (269) • DGFS (469) • DGTR/L (476) • HELIIR/L (355) • HELIR/L (266) • HFAER/L-4 (565) • HFAER/L-5T, 6T (566) • HFAIR/L-4 (572) • HFAIR/L-DG (573) • HFFR/L-T (564) • HFHR/L-4T (559) • HFHR/L-5T (560) • HFHR/L-6T (561) • HFIR/L-MC (574) • HFPAD-3 (562) • HFPAD-4 (563) • HFPAD-5 (563) • HFPAD-6 (564) • HFPAD-JHP (562) • HGAER/L-3 (565) • HGAIR/L-3 (568) • HGFH (268) • HGHR/L-3 (558) • HGPAD (267) • HGPAD-JHP (267) • IM-HFIR-MC (574) OAL LH TGDR/L External Holders for Turning, HF H Grooving and Profiling HBH CDX WF B CWN-CWX Right-hand shown Designation CWN(1) CWX(2) CDX(3) H HF B OAL LH WF HBH Insert TGDR/L 1616-3M 3.00 3.00 7.50 16.0 16.0 16.0 100.00 30.5 14.80 6.0 TGMF 3 SR M5X12 DIN912 HW 4.0(a) TGDR/L 2020-3M 3.00 3.00 7.50 20.0 20.0 20.0 125.00 30.5 18.70 - TGMF 3 SR M5X12 DIN912 HW 4.0(a) TGDR/L 2525-3M 3.00 3.00 7.50 25.0 25.0 25.0 140.00 30.5 23.70 - TGMF 3 SR M5X12 DIN912 HW 4.0(a) TGDR/L 1616-4M 4.00 5.00 9.00 16.0 16.0 16.0 100.00 32.2 14.20 6.0 TGMF 4/TGMF 5 SR M5X12 DIN912 HW 4.0(a) TGDR/L 2020-4M 4.00 5.00 9.00 20.0 20.0 20.0 125.00 32.2 18.20 6.0 TGMF 4/TGMF 5 SR M5X12 DIN912 HW 4.0(a) TGDR/L 2525-4M 4.00 5.00 15.50 25.0 25.0 25.0 140.00 34.0 23.20 - TGMF 4/TGMF 5 SR M5X12 DIN912 HW 4.0(a) TGDR/L 2525-5M 5.00 5.00 18.00 25.0 25.0 25.0 140.00 37.0 22.70 - TGMF 5 SR M5X12 DIN912 HW 4.0(a) TGDR/L 3232-5M 5.00 5.00 22.00 32.0 32.0 32.0 150.00 45.0 29.80 - TGMF 5 SR M6X12DIN912 HW 5.0(a) TGDR/L 2525-6M 6.00 6.35 22.00 25.0 25.0 25.0 150.00 43.0 22.50 - TGMF 6 SR M6X16 DIN912 HW 5.0(a) TGDR/L 3232-6M 6.00 6.35 22.00 32.0 32.0 32.0 150.00 43.0 29.50 - TGMF 6 SR M6X16 DIN912 HW 5.0(a) • For user guide, see pages 419-428, 432-436 (1) Minimum cutting width (2) Maximum cutting width (3) Grooving depth is limited by the insert (a) For optional key with limited tightening torque see page 427 For inserts, see pages: TGMA (272) • TGMF (full radius) (272) • TGMF/P (272) HOLDER: MAHPR WF(assembly) OAH HF OAL TGPAD WF(holder) OHN CDX WF (adapter) Adapters Carrying TGMF / TGMP Groove-Turn Inserts HOLDER: MAHL WB_2 WB CWN-CWX Left-hand shown • WF(assembly)=WF(holder)+WF(adapter) Designation CWN(1) CWX(2) CDX(3) WF(4) WB WB_2 OHN(5) OAL HF OAH TGPAD 3R/L-T9 3.00 3.00 9.00 4.00 2.40 5.2 12.7 37.20 24.0 30.0 TGPAD 4R/L-T16 4.00 5.00 16.00 3.50 3.40 5.2 17.2 41.70 24.0 30.0 TGPAD 5R/L-T16 5.00 5.00 16.00 3.00 4.40 5.2 17.2 41.70 24.0 30.0 TGPAD 6R/L-T22 6.00 6.35 22.00 3.50 5.00 6.0 23.2 47.10 24.0 32.0 • For user guide, see pages 419-428, 432-436 (1) Minimum cutting width (2) Maximum cutting width (3) Grooving depth is limited by the insert (4) WF(adapter) (5) Minimum overhang For inserts, see pages: TGMA (272) • TGMF (full radius) (272) • TGMF/P (272) 270 ISCAR