Каталог Iscar дисковые фрезы и фрезерные пластины 2022 - страница 156

MILLING INSERTS
W1
H490 ANKX/ANCX-17
Double-Sided Rectangular Inserts


1
with 4 Helical Cutting Edges L


3
BS RE S

Recommended
Dimensions Tough 1 Hard
Machining Data


DT7150
ap fz


IC5400


IC5100
IC330
IC845
IC830

IC380
IC808
IC810
Designation L RE S W1 BS (mm) (mm/t)
H490 ANKX 170604PNTR 16.70 0.40 10.40 11.20 4.70 • 0.80-15.00 0.15-0.30
H490 ANCX 170608PDR 16.70 0.80 10.40 11.20 4.70 • • • • • 1.20-15.00 0.10-0.18
H490 ANKX 1706PNTR-CS (1) 16.70 0.80 10.40 11.20 4.70 • 1.20-15.00 0.15-0.22
H490 ANKX 1706PNTR-RM 16.70 0.80 10.40 11.20 4.70 • • • 1.20-15.00 0.20-0.40
H490 ANKX 170608PNTR 16.70 0.80 10.40 11.20 4.70 • • • • • • • • 1.20-15.00 0.15-0.30
H490 ANKX 170612PNTR 16.90 1.20 10.50 11.00 3.50 • • 1.60-15.00 0.15-0.30
H490 ANKX 170616PNTR 16.90 1.60 10.50 11.00 3.10 • • 2.00-15.00 0.15-0.30
H490 ANKX 170620PNTR 16.90 2.00 10.50 11.00 2.70 • • 2.40-15.00 0.15-0.30
H490 ANKX 170624PNTR 16.90 2.40 10.50 11.00 2.30 • • 2.80-15.00 0.15-0.30
• ANKX-utility inserts. ANCX-precision inserts • For cutting speed recommendations, see pages 542-547
(1) The maximum feed per tooth for chip splitting effect is up to 0.22 mm/t.
For tools, see pages: H490 E90AX-17 (33) • H490 F90AX-17 (213) • H490 SM-17 (249)


REN 3º30’ Rd°

H490 ANKX 1706-FF RE
Single-Sided Rectangular
Inserts with 2 Helical Cutting lNSL
Edges for Fast Feed Milling
at Small Depths of Cut BS AE
APMX
W1 S

Recommended
Dimensions
Machining Data

ap fz
Designation INSL S W1 BS RE Rg(1) REN APMX AE IC830 (mm) (mm/t)
H490 ANKX 1706R15T-FF 16.80 7.80 11.70 4.60 1.60 2.85 15.00 2.00 6.1 • 0.50-2.00 1.00-2.00
• The cutting diameter of the tool is 1.5 mm larger than the nominal diameter when using this insert • No tool radius modifications is required • At D.O.C. larger than APMX,
regular insert feed should be applied • For cutting speed recommendations, see pages 542-547
(1) Radius for programming
For tools, see pages: H490 E90AX-17 (33) • H490 F90AX-17 (213)


IC
H690 TNKX/TNCX 1005 2
Triangular Inserts with 6
APMX INSL
1


Helical Cutting Edges for
90° Shoulder Accuracy 3
S BS RE

Recommended
Dimensions Tough 1 Hard
Machining Data
IC5400


ap fz
IC330
IC830


IC808
IC810


Designation INSL APMX IC S RE BS (mm) (mm/t)
H690 TNKX 100504PNTR 8.48 8.00 6.20 4.70 0.40 0.80 • • • • • 0.80-8.00 0.08-0.15
H690 TNCX 100504 PDR (1) 8.60 8.00 6.20 4.70 0.40 0.70 • • • 0.80-8.00 0.08-0.13
H690 TNKX 100508PNTR 8.60 8.00 6.20 4.70 0.80 0.40 • • • 1.20-8.00 0.08-0.15
• For cutting speed recommendations, see page 473
(1) Peripherally ground
For tools, see pages: H690 E90AX-10 (28) • H690 F90AX-10 (201)


472 ISCAR