Каталог ARNO инструмент и сменные пластины для токарной обработки и обработки резьбы - страница 452

Tensile strength [N/mm2] AP2310 AP2320 AP2335 AP5210 AL10 AM15C AM25C AM350 AM35C AR27C AR270 AR370 Recommended Cutting Data Turning – Carbide coated Cutting speed Vc [m/min] ISO Material ca. 0,15% C 350 300 - 400 250 - 350 180 - 270 220 - 370 220 - 320 220 - 320 150 - 260 180 - 230 170 - 240 200 - 270 200 - 260 190 - 240 Unalloyed steel and cast steel ca. 0,45% C 650 260 - 350 210 - 300 170 - 230 180 - 330 180 - 290 180 - 250 140 - 210 170 - 190 150 - 200 180 - 230 180 - 220 170 - 200 ca. 0,75% C 1000 240 - 300 180 - 230 160 - 210 150 - 290 150 - 250 140 - 200 120 - 180 100 - 140 80 - 150 120 - 180 120 - 180 100 - 150 600 220 - 300 180 - 270 160 - 220 180 - 320 180 - 280 180 - 250 140 - 210 170 - 190 150 - 200 210 - 260 180 - 220 170 - 200 P Low alloyed steel and cast steel 900 180 - 260 160 - 220 140 - 180 170 - 290 170 - 250 160 - 220 130 - 190 90 - 150 80 - 160 120 - 190 120 - 180 100 - 1601200120 - 220100 - 200100 - 160150 - 260150 - 220140 - 200120 - 18070 - 13060 - 140120 - 160120 - 15080 - 140 High alloyed steel, high alloyed annealed 700 150 - 220 130 - 200 130 - 180 80 - 180 - 140 - 230 120 - 200 120 - 200 110 - 170 140 - 200 140 - 180 130 - 170 tool steel and cast steel hardened and tempered 1100 70 - 150 70 - 140 70 - 120 40 - 150 - 110 - 200 100 - 160 50 - 100 60 - 130 100 - 160 100 - 150 80 - 130 ferritic / martensitic, annealed 700 - - - 40 - 140 170 - 290 170 - 260 140 - 240 140 - 180 110 - 180 170 - 230 170 - 220 130 - 180 Stainless steel and cast steel martensitic, hardened and tempered 1000 - - - 40 - 120 140 - 280 110 - 200 110 - 200 110 - 160 90 - 160 130 - 190 130 - 180 110 - 160 M Stainless steel and cast steel austenitic and austenitic/ferritic 450 - 600 - - - 70 - 150 140 - 280 210 - 250 100 - 170 120 - 190 100 - 170 150 - 220 150 - 200 100 - 170chilled600 - 900---35 - 120-100 - 17080 - 15080 - 150---- pearlitic, ferritic 500 - 700 - - - 180 - 350 180 - 300 210 - 250 170 - 230 - - 120 - 180 - - Cast iron pearlitic, martensitic 700 - 850 - - - 160 - 300 160 - 280 90 - 130 90 - 120 - - 120 - 180 - - 800 - 1100 - - - 120 - 270 120 - 240 90 - 130 90 - 120 - - 100 - 150 - - K Cast iron with nodular graphite ferritic 550 - - - 140 - 230 140 - 230 210 - 250 170 - 230 - - 120 - 170 120 - 160 - pearlitic 800 - - - 120 - 170 120 - 170 90 - 130 90 - 120 - - 120 - 190 120 - 180 - ferritic 450 - - - 150 - 210 150 - 210 210 - 250 170 - 230 - - 150 - 230 - - Malleable cast iron pearlitic 750 - - - 150 - 210 150 - 210 90 - 130 90 - 120 - - 120 - 170 - - not heat treatable 200 - - - - - - - - - - - - Aluminum alloys, long chipping heat treatable, heat treated 350 - - - - - - - - - - - - ≤ 12% Si, hardened 250 - - - - - - - - - - - - Casted aluminum alloys ≤ 12% Si, heat treatable, heat treated 300 - - - - - - - - - - - - ≤ 12% Si, not heat treatable 450 - - - - - - - - - - - - N Copper and copper alloys Lead alloys, Pb > 1%Brass, bronze 400 - - - - - - - - - - - -300------------ (brass / bronze) Aluminum bronze 500 - - - - - - - - - - - - Copper and electrolyte copper 200 - - - - - - - - - - - - Duroplastics - - - - - - - - - - - - Non-ferrous materials Reinforced plastics - - - - - - - - - - - - Hard rubber - - - - - - - - - - - - Fe-alloyed annealed 700 - - - 20 - 70 20 - 50 - - 20 - 40 - - 20 - 50 20 - 40 Fe-alloyed hardened 950 - - - 20 - 70 20 - 50 - - 15 - 35 - - 20 - 50 15 - 35 High temperature resistant alloys Ni- oder Co- based annealed 800 - - - 15 - 60 15 - 40 - - 8 - 25 - - 15 - 40 10 - 30 S Ni- oder Co- based casting 1100 - - - 15 - 50 15 - 30 - - 4 - 15 - - 10 - 25 5 - 18 i Ni- oder Co- based hardened 1200 - - - 15 - 50 15 - 30 - - 4 - 15 - - 20 - 35 5 - 18Titanium alloys, high strengthPure titanium500 - 700----------20 - 60- Alpha- and beta-alloys, hardened 700 - 1000 - - - - - - - - - - 25 - 45 - hardened and tempered 1000 - 1350 - - - - - - - - - - - - Hardened steel H Hard cast iron hardened and tempered 1350 - 1700 - - - - - - - - - - - -casting1350------------ Hardened cast iron hardened and tempered 1900 - - - - - - - - - - - - The datas cutting speeds given are approximate values. More grades on the It is necessary to adjust them to the individual machining operation. following pages. 452 ARNO®-Werkzeuge | Drehen | Turning | Точение