Indexable Endmills α° Chipbreaker Wavemill Series WEX Type Recommended Cutting Conditions WEX3000 Series 16mm Cutter: WEX30325E Insert: AXMT170508PEER - 5mm Cutting Data: ap = 5mm, ae = 16mm, dry Coated Carbide „Diamond like Carbon“Coated Carbide ACP100 ACP200 ACP300 ACK200 ACK300 ACM200 ACM300 DL1000 ISO Material HB Feed Rate (mm/tooth) 0,12 0,25 0,35 0,12 0,25 0,35 0,12 0,25 0,35 0,12 0,25 0,35 0,12 0,25 0,35 0,12 0,25 0,35 0,12 0,25 0,35 0,05 0,15 0,25 Cutting Speed vc (m/min) Unalloyed steel, <0, 15%C, annealed 125 G 400 370 350 370 350 330 350 330 310 „ , <0, 45%C, annealed 190 G 300 270 250 270 250 230 250 230 210 „ , <0, 45%C, tempered 250 G 250 220 200 220 200 180 200 180 160 „ , <0, 75%C, annealed 270 G 200 170 150 180 160 140 160 140 120 „ , <0, 75%C, tempered 300 G 150 120 100 120 100 80 100 80 60 P Low alloyed steel, annealed 180 G 280 250 230 250 230 210 230 210 190 „ , tempered 275 G 180 150 130 160 140 120 140 120 100 „ , tempered 300 G 160 130 110 140 120 100 120 100 80 „ , tempered 350 G 130 100 80 110 90 70 90 70 50 High alloyed and tool steel, annealed 200 G 250 220 200 220 200 180 200 180 160 „ , tempered 325 G 130 100 80 100 80 60 80 60 40 Stainless steel, ferritic/martensitic, annealed 200 E 185 165 135 165 150 120 M Martensitic, tempered 240 EH 170 150 120 150 135 110 Austenitic, plunged 180 E 200 180 150 180 160 135 K Grey cast ironNodular cast iron GG 300 270 250 270 250 230200 170 150 170 150 130 S High tempered resist. alloys, Fe based, annealed 300 E„, hardened 330E 50 30 45 2550304525 Aluminium alloy, Si < 13% S 1000 750 500 N Aluminium alloy, Si > 13% S 250 200 170 Copper alloy S 350 330 300 The above recommended cutting conditions are meant as a guide. Actual conditions will depend on the individual machine, work shape and clamping. They will need to be adjusted according to machine rigidity, work clamp rigidity, cutting depth and other factors. For groove milling, reduce the feed rate approximately 70% of the corresponding value shown above. Recommended Values for Helical Milling and Ramping Helical Boring Recommended Values for Helical and Plunging ≤ Min. Diameter Cutter WEX1000 (AXMT06...) WEX2000 (AX T12...) WEX3000 (AX T17...) ø External Helical Plunging Helical Plunging Helical PlungingCenter uncut portioncannot be removedby traverse cuttingDiameterWork DiameterMax. Ram-Work DiameterMax. Ram-Work DiameterMax. Ram-ØDcMin.Max.ping AngleMin.Max.ping AngleMin.Max.ping Angle with the same cutter. 10 16,0 18,0 2°30' 12 20,0 22,0 1°45' 14 24,0 26,0 1°25' 25,0 27,0 1°40' ≥ Max. Diameter 16 28,0 30,0 1°00' 29,0 31,0 1°20' 18 32,0 34,0 0°45' 33,0 35,0 1°10' ø Center uncut portion 20 36,0 38,0 0°30' 37,0 39,0 1°00' can be removed by 22 41,0 43,0 0°50' traverse cutting with 25 46,0 48,0 0°30' 47,0 49,0 0°45' 44,5 48,0 1°30' the same cutter. 28 53,0 55,0 0°45' 50,5 54,0 1°10' 30 57,0 59,0 0°40' 54,5 58,0 1°10' 32 60,0 62,0 0°25' 61,0 63,0 0°35' 58,5 62,0 1°00' Plunging 35 64,5 68,0 0°50'4076,078,00°20'77,079,00°25'74,578,00°45' Use at ≤ α° 50 96,0 98,0 0°15' 97,0 99,0 0°20' 94,5 98,0 0°30' 63 122,0 124,0 0°10' 123,0 125,0 0°15' 120,5 124,0 0°20' 80 154,5 158,0 0°15' 100 125 The above recommended values are for a nose radius of 0,8mm. H26