Общий каталог SGS 2021 - страница 35

METRIC Z-Carb-HPR 37° POS TOLERANCES (mm) 5 ≠ 6 DIAMETER DC = +0,000/–0,030 DCON = h6 RE = +0,000/–0,050 >6–10 DIAMETER DC = +0,000/–0,040DCON = h6 LFAPMX RE = +0,000/–0,050 >10–25 DIAMETER DC DCON DC = +0,000/–0,050DCON = h6 NCD Z5MCR RE = +0,000/–0,050 RE METRIC SERIES mm EDP NO. • An ideal balance of NON- helix, indexing, flute CUTTING TI-NAMITE-A TI-NAMITE-M depth, rake and relief CUTTING LENGTH OVERALL SHANK CORNER CENTER TI-NAMITE-A TI-NAMITE-A (TA) TI-NAMITE-M TI-NAMITE-M (TM)DIAMETEROF CUTLENGTHDIAMETERRADIUSDIAMETER(TA)(TA)W/INTERNAL(TM)(TM)W/INTERNAL• Variable indexing for DC APMX LF DCON RE NCD W/FLAT COOLANT W/ FLAT COOLANT chatter supression and patented edge 6,0 9,0 54,0 6,0 0,5 2,11 48000 – – 47000 – – geometry for shearing 6,0 13,0 57,0 6,0 0,3 2,11 48001 – – 47001 – – and strength • Chatter-free geometry 6,0 13,0 57,0 6,0 0,5 2,11 47120 – – 47002 – – allows deep cutting and high speed machining 6,0 13,0 57,0 6,0 1,0 2,11 48002 – – 47003 – – • Central coolant hole 6,0 13,0 57,0 6,0 1,5 2,11 48003 – – 47004 – – delivers coolanteffectively to the 8,0 11,0 58,0 8,0 0,5 2,79 48004 – – 47005 – – cutting zone enhancing chip removal when 8,0 18,0 63,0 8,0 0,5 2,79 47121 – – 47006 – – pocketing or slotting 8,0 18,0 63,0 8,0 1,0 2,79 47122 – – 47007 – – • Enhanced cornergeometry with tight 8,0 18,0 63,0 8,0 1,5 2,79 48005 – – 47008 – – tolerance corner radii 8,0 18,0 63,0 8,0 2,0 2,79 48006 – – 47009 – – • Excels at roughing,ramping, high speed 10,0 13,0 66,0 10,0 1,0 2,79 48007 – – 47010 – – machining and finishingin a variety of materials 10,0 22,0 72,0 10,0 0,5 3,51 47123 – – 47011 – – • Recommended for 10,0 22,0 72,0 10,0 1,0 3,51 47124 – – 47012 – – materials ≤ 45 HRc(≤ 420 Bhn) 10,0 22,0 72,0 10,0 1,5 3,51 48008 – – 47013 – – 10,0 22,0 72,0 10,0 2,0 3,51 48009 – – 47014 – – STEELS 10,0 22,0 72,0 10,0 2,5 3,51 48010 – – 47015 – – STAINLESS STEELS 12,0 15,0 73,0 12,0 1,0 4,19 48011 48029 – 47016 47024 – CAST IRON 12,0 26,0 83,0 12,0 0,5 4,19 47125 47128 47160 47017 47025 47161 HIGH TEMP ALLOYS 12,0 26,0 83,0 12,0 0,76 4,19 47126 47129 47162 47018 47026 47163 TITANIUM 12,0 26,0 83,0 12,0 1,0 4,19 47127 47130 47164 47019 47027 47165 HARDENED STEELS 12,0 26,0 83,0 12,0 1,5 4,19 48012 48030 47166 47020 47028 47167 12,0 26,0 83,0 12,0 2,0 4,19 48013 48031 47168 47021 47029 47169 For patent 12,0 26,0 83,0 12,0 2,5 4,19 48014 48032 47170 47022 47030 47171 information visit www.ksptpatents.com 12,0 26,0 83,0 12,0 3,0 4,19 48015 48033 47172 47023 47031 47173 16,0 19,0 82,0 16,0 1,0 5,59 48016 48034 48056 47032 47039 47046 16,0 19,0 82,0 16,0 1,5 5,59 48070 – – 48071 – – 16,0 35,0 92,0 16,0 1,0 5,59 47131 48035 47134 47033 47040 47047 16,0 35,0 92,0 16,0 1,5 5,59 48017 48036 48057 47034 47041 47048 continued on next page www.kyocerEaN-DsgMstILoLoSl.com END MILLS 35