Общий каталог Mitsubishi 2020 - 2021 - страница 1396

Предыдущая страница Следующая страница

Навигация

( inch) &2.000", &2.500" &3.000", &4.000", &4.921", &6.299" & 3.000", & 4.000" zOverhang Length (&50 mm, &63 mm) (&80 mm, &100 mm, &125 mm, &160 mm) (& 80 mm, & 100 mm) (Arbor type) (Arbor type) (Arbor type) AJXU09 Type ( & 2.000") AJXU14 TypeAJXU12 Type (& 2.500")AJX14TypeAJXU12 Type 5 (Number of Teeth) 4 or 5 or 6 or 7 or 8(Number of Teeth)6 or 7 (Number of Teeth) Over-hangAxial Feed perDepth ofToothCut(IPT)Over-hangAxialFeed perDepth ofToothCut(IPT)Over-hangAxialFeed perDepth ofToothCut(IPT)Overhang Length 6.0 .053 .051 7.0 .059 .059 7.0 .053 .051 (GL:Gage Length) 10.0 .046 .043 12.0 .051 .051 12.0 .046 .043 14.0 .039 .035 18.0 .039 .039 18.0 .035 .031 6.0 .053 .051 7.0 .059 .059 7.0 .053 .051 xMain Spindle Speedn(min-1)=(Recommended Cutting Speed x 12)÷(DCX x 3.14) 10.0 .046 .043 12.0 .051 .051 12.0 .046 .043 cTable Feed Rate 14.0 .039 .035 18.0 .039 .039 18.0 .035 .031 vf(IPM)=n x feed per tooth fz x number of teeth 6.0 .046 .051 7.0 .051 .059 7.0 .046 .051 vRecommended width of cut (ae) is more than 60% of cutting edge diameter. 10.0 .039 .043 12.0 .043 .051 12.0 .039 .043 bThe cutting condition on the left are guide when using a 14.0 .032 .035 18.0 .031 .039 18.0 .028 .031 CAT50 size holder. In case of CAT40 and HSK63 machines, 6.0 .046 .051 7.0 .051 .059 7.0 .046 .051 a cutter diameter of under 1.5 inch is recommended. In thiscase, reduce the depth of cut and table feed rate. 10.0 .039 .043 12.0 .043 .051 12.0 .039 .043 nUse of ST chip breaker with a tougher cutting edge is 14.0 .032 .035 18.0 .031 .039 18.0 .028 .031 recommended for interrupted cutting. 6.0 .046 .043 7.0 .051 .051 7.0 .046 .043 mA cutter body with a coarse pitch is recommended for use in unstable conditions such as a long tool overhang. 10.0 .039 .035 12.0 .043 .043 12.0 .039 .035 ,Use “sharp” JM chip breaker to lower cutting forces or when 14.0 .032 .028 18.0 .031 .031 18.0 .028 .024 there is a long tool overhang. 6.0 .053 .043 7.0 .059 .051 7.0 .053 .043 .Large chips are generated when machining with the AJX. To avoid chip jamming-related problems, machine using an 10.0 .046 .035 12.0 .051 .043 12.0 .046 .035 air blow to disperse the chips effectively. 14.0 .039 .028 18.0 .039 .031 18.0 .035 .024 /The maximum depth of cut JL chip breaker is different in the 6.0 .053 .059 7.0 .059 .067 7.0 .053 .059 insert size. 06 size is up to .024 inch, 08 size is up to .035 inch, and 09, 12, 14 size is up to .047 inch. 10.0 .046 .051 12.0 .051 .059 12.0 .046 .051 14.0 .039 .039 18.0 .039 .047 18.0 .035 .035 6.0 .046 .051 7.0 .051 .059 7.0 .046 .051 10.0 .039 .043 12.0 .043 .051 12.0 .039 .043 14.0 .032 .035 18.0 .031 .039 18.0 .028 .031 6.0 .047 .024 7.0 .047 .024 7.0 .047 .024 L 10.0 .039 .016 12.0 .039 .016 12.0 .039 .016 14.0 .031 .012 18.0 .031 .012 18.0 .031 .012 6.0 .032 .039 7.0 .035 .043 7.0 .032 .039 10.0 .025 .031 12.0 .028 .035 12.0 .025 .031 ─ ─ ─ ─ ─ ─ ─ ─ ─ * Depth of cut of JL breaker is up to .047 inch. L221 INDEXABLE MILLING