High-Feed Mills • VXF-07
Recommended Starting Speeds [m/min]*
| Material Group | | WP25PM | | | WP40PM | | | WS40PM | | | WU10PM | |
| 1 | 395 | 340 | 325 | 355 | 310 | 295 | – | – | – | – | – | – |
| 2 | 330 | 290 | 240 | 300 | 260 | 215 | – | – | – | – | – | – |
| P 3 | 305 | 260 | 210 | 275 | 235 | 190 | – | – | – | – | – | – |
| 4 | 270 | 220 | 180 | 245 | 205 | 160 | – | – | – | – | – | – |
| 5 | 220 | 205 | 180 | 205 | 185 | 160 | 205 | 175 | 145 | – | – | – |
| 6 | 200 | 150 | 120 | 180 | 140 | 110 | 180 | 130 | 95 | – | – | – |
| 1 | 245 | 215 | 200 | 235 | 205 | 185 | 250 | 205 | 170 | – | – | – |
| M 2 | 220 | 190 | 155 | 210 | 180 | 150 | 215 | 175 | 145 | – | – | – |
| 3 | 170 | 145 | 115 | 155 | 140 | 110 | 175 | 130 | 100 | – | – | – |
| 1 | 275 | 245 | 220 | – | – | – | – | – | – | 355 | 320 | 290 |
| K 2 | 215 | 190 | 180 | – | – | – | – | – | – | 275 | 245 | 230 |
| 3 | 180 | 160 | 145 | – | – | – | – | – | – | 235 | 210 | 190 |
| 1 | 50 | 40 | 30 | 50 | 40 | 35 | 50 | 40 | 30 | – | – | – |
| S 2 | 50 | 40 | 30 | 50 | 40 | 35 | 50 | 40 | 30 | – | – | – |
| 3 | 60 | 50 | 30 | 60 | 50 | 35 | 60 | 50 | 30 | – | – | – |
| 4 | 85 | 60 | 40 | 80 | 60 | 40 | 70 | 60 | 35 | – | – | – |
| H 1 | 145 | 110 | 85 | – | – | – | – | – | – | 190 | 155 | 110 |
NOTE: FIRST choice starting speeds are in bold type. As the average chip thickness increases, the speed should be decreased. *Material groups P, M, K, and H show recommended starting speeds for dry machining. For wet machining, reduce speed by 20%. *Material groups N and S show recommended starting speeds for wet machining. Not recommended for dry machining.
Recommended Starting Feeds [mm]
| 0,60 Axia | l Dep | th of C | ut (AP | 1) | | | | | | | | Lig Mach | ht ining | General Purpose | Heavy Machining |
| Insert Geometry | | 5% | | | 10% | Recomme in Relatio | nded S n to % | tarting F of Radial 20% | eed per Engage | Tooth (F ment (ae | z) ) 30% | | | 40–100% | Insert Geometry |
| .E..MM | 0,46 | 1,32 | 2,43 | 0,32 | 0,89 | 1,53 | 0,24 | 0,65 | 1,09 | 0,21 | 0,56 | 0,94 | 0,19 | 0,52 0,85 | .E..MM |
| .S..MH | 0,84 | 1,84 | 3,12 | 0,59 | 1,21 | 1,85 | 0,43 | 0,87 | 1,30 | 0,38 | 0,75 | 1,12 | 0,34 | 0,69 1,02 | .S..MH |
At 0,90 Axial Depth of Cut (AP1)
| Insert Geometry | | 5% | | | i 10% | Recomm n Relatio | ended S n to % | tarting F of Radia 20% | eed per l Engage | Tooth (F ment (ae | z) ) 30% | | | 40–100% | | Insert Geometry |
| .E..MM | 0,42 | 1,21 | 2,20 | 0,30 | 0,83 | 1,41 | 0,22 | 0,60 | 1,01 | 0,19 | 0,52 | 0,87 | 0,18 | 0,48 | 0,79 | .E..MM |
| .S..MH | 0,78 | 1,68 | 2,79 | 0,55 | 1,12 | 1,71 | 0,40 | 0,81 | 1,21 | 0,35 | 0,70 | 1,04 | 0,32 | 0,64 | 0,94 | .S..MH |
At 0,70 Axial Depth of Cut (AP1)
| Insert Geometry | | 5% | | | R i 10% | ecomm n Relatio | ended S n to % | tarting F of Radia 20% | eed per l Engage | Tooth (F ment (ae | z) ) 30% | | | 40–100% | | Insert Geometry |
| .E..MM | 0,37 | 1,06 | 1,89 | 0,27 | 0,73 | 1,24 | 0,20 | 0,53 | 0,89 | 0,17 | 0,46 | 0,77 | 0,16 | 0,42 | 0,70 | .E..MM |
| .S..MH | 0,68 | 1,46 | 2,35 | 0,48 | 0,98 | 1,49 | 0,36 | 0,71 | 1,07 | 0,31 | 0,62 | 0,92 | 0,28 | 0,56 | 0,84 | .S..MH |
NOTE: Use “Light Machining” values as starting feed rate.
Каталог Widia инструмент для обработки отверстий 2017
Каталог Widia токарный инструмент 2020
Каталог Widia монолитный инструмент 2017
Каталог Widia техническое руководство по разверткам
Каталог Widia инструментальная оснастка