Каталог Widia достижения 2020 - страница 138

Предыдущая страница Следующая страница

Навигация

Indexable Drills • Top Cut 4

Top Cut 4 • Insert Selection Guide

Material GroupGeometryStable Cuttin periphery insertg Conditions centre insertUnstable Cutt periphery inserting Conditions centre insertInterrupted Cu periphery inserttting Conditions centre insert
P1V38WU25CHWU40PHWU40PHWU40PHWU40PHWU40PH
P2–P4V34WPK10CHWU40PHWU25CHWU40PHWU40PHWU40PH
P5–P6V36WU25CHWU40PHWU40PHWU40PHWU40PHWU40PH
M1–M3V36WU25CHWU40PHWU40PHWU40PHWU40PHWU40PH
K1–K3V34WPK10CHWU40PHWU40PHWU40PHWU40PHWU40PH
N1–N4V36WN10PHWN10PHWN10PHWN10PHWN10PHWN10PH
S1–S4V38WU40PHWU40PHWU40PHWU40PHWU40PHWU40PH

Top Cut 4 • Cutting Data • Metric

GradeCutting Speed m/min— VcRecommenMetric ded Feed Rateper Revolution
MtilTl12001399140018991900239924002999
aeraoo,–,,–,,–,,–,
GroupGeometrycentreperipheryminStartmaxDiameterInsert Size AInsert Size BInsert Size CInsert Size D
P0-V38WU40PHWU25CH120180260mm/rev0,06–0,080,08–0,110,10–0,130,11–0,14
P1-V38WU40PHWU25CH120180260mm/rev0,06–0,100,08–0,130,10–0,150,11–0,16
P2-V34WU40PHWU25CH120190280mm/rev0,06–0,100,08–0,150,10–0,160,11–0,17
P3-V34WU40PHWPK10CH120200310mm/rev0,08–0,150,10–0,160,11–0,180,12–0,20
P4-V34WU40PHWPK10CH120190310mm/rev0,08–0,150,10–0,160,11–0,180,12–0,20
P5-V36WU40PHWU25CH120180250mm/rev0,06–0,100,08–0,140,10–0,150,11–0,16
P6-V36WU40PHWU25CH120160210mm/rev0,06–0,100,08–0,140,10–0,150,11–0,16
M1-V38WU40PHWU40PH120160240mm/rev0,06–0,110,07–0,110,08–0,120,10–0,14
M2–V36WU40PHWU40PH110140210mm/rev0,06–0,100,07–0,110,08–0,120,10–0,14
M3-V36WU40PHWU40PH100120200mm/rev0,06–0,100,07–0,110,08–0,120,10–0,14
K1-V34WU25CHWPK10CH120200280mm/rev0,08–0,140,08–0,160,10–0,180,12–0,24
K2-V34WU40PHWPK10CH100180260mm/rev0,08–0,140,08–0,160,10–0,180,12–0,24
K3-V34WU40PHWPK10CH100170240mm/rev0,08–0,140,08–0,160,10–0,180,12–0,24
N1-V36WN10PHWN10PH250350500mm/rev0,06–0,100,08–0,140,10–0,150,11–0,16
N2-V36WN10PHWN10PH150300450mm/rev0,06–0,100,08–0,140,10–0,150,11–0,16
N3-V36WN10PHWN10PH80120150mm/rev0,06–0,100,07–0,110,08–0,120,10–0,14
S3-V38WU40PHWU40PH203045mm/rev0,08–0,120,08–0,130,10–0,150,12–0,19
S4-V38WU40PHWU40PH354065mm/rev0,08–0,120,08–0,130,10–0,150,12–0,19
GradeCutting Speed m/min— Vc
MaterialTool30,00–36,9937,00–45,9946,00–56,9957,00–68,00
GroupGeometrycentreperipheryminStartmaxDiameterInsert Size EInsert Size FInsert Size GInsert Size H
P0-V38WU40PHWU25CH120180260mm/rev0,13–0,160,15–0,180,16–0,230,17–0,24
P1-V38WU40PHWU25CH120180260mm/rev0,13–0,170,15–0,190,16–0,240,17–0,25
P2-V34WU40PHWU25CH120190280mm/rev0,13–0,200,15–0,210,16–0,280,17–0,30
P3-V34WU40PHWPK10CH120200310mm/rev0,16–0,240,16–0,240,18–0,300,19–0,32
P4-V34WU40PHWPK10CH120190310mm/rev0,14–0,220,16–0,240,18–0,300,19–0,32
P5-V36WU40PHWU25CH120180250mm/rev0,13–0,180,15–0,200,16–0,280,17–0,30
P6-V36WU40PHWU25CH120160210mm/rev0,13–0,180,15–0,200,16–0,280,17–0,29
M1-V38WU40PHWU40PH120160240mm/rev0,12–0,170,14–0,210,16–0,230,16–0,24
M2–V36WU40PHWU40PH110140210mm/rev0,12–0,170,14–0,210,16–0,230,16–0,24
M3-V36WU40PHWU40PH100120200mm/rev0,12–0,170,14–0,210,16–0,230,16–0,24
K1-V34WU25CHWPK10CH120200280mm/rev0,14–0,260,16–0,300,18–0,320,20–0,36
K2-V34WU40PHWPK10CH100180260mm/rev0,14–0,260,16–0,300,18–0,320,20–0,36
K3-V34WU40PHWPK10CH100170240mm/rev0,14–0,260,16–0,300,18–0,320,20–0,36
N1-V36WN10PHWN10PH250350500mm/rev0,13–0,180,15–0,200,16–0,280,17–0,30
N2-V36WN10PHWN10PH150300450mm/rev0,13–0,180,15–0,200,16–0,280,17–0,30
N3-V36WN10PHWN10PH80120150mm/rev0,12–0,170,14–0,210,16–0,230,16–0,24
S3-V38WU40PHWU40PH203045mm/rev0,14–0,210,16–0,240,18–0,260,20–0,30
S4-V38WU40PHWU40PH354065mm/rev0,14–0,210,16–0,240,18–0,260,20–0,30

NOTE: All speed conditions are for stable conditions. For unstable conditions, it is suggested to reduce starting speeds by 10%. For interrupted cuts, reduce by 20%. For 4 x D, it is highly recommended to start with feed and speed values reduced by 10% less than above data. For 5 x D, diameter range 12–23,99mm (insert sizes A to C), it is highly recommended to start with feed and speed values reduced by 20% less than above data. For 5 x D, diameter range 25–68mm (inserts sizes D to H), it is highly recommended to start with feed and speed values reduced by 15% less than above data. For 4 x D and 5 x D, it is recommended to reduce feed rate during entry and exit by 30–50%.