Брошюра Tungaloy новая продукция - страница 93

Предыдущая страница Следующая страница

Навигация

Tool dia.:DCX(mm),Numberof revolutions:n (min-1), Feed speed:Vf(mm/min), Max. depth of cut:ap= 0.5 mm
ø22ø25ø28ø30ø32ø35ø40ø50
VfVfVfVfVfVfVfVf
nCICT = 3CICT = 4nCICT = 4 CICT = 5nCICT = 4CICT = 5nCICT = 4 CICT = 5nCICT = 5CICT = 6nCICT = 5CICT = 6nCICT = 5CICT = 6nCICT =5 CICT = 8
2,8908,67011,5602,55010,200 12,7502,2709,08011,3502,1208,480 10,600 Vc =200 m/m1,990 in,fz =9,950 1 mm/t11,9401,8209,10010,9201,5907,9509,5401,2706,35010,160
2,8908,67011,5602,55010,200 12,7502,2709,08011,3502,1208,480 10,600 Vc =200 m/m1,990 in,fz =9,950 1 mm/t11,9401,8209,10010,9201,5907,9509,5401,2706,35010,160
2,1705,2106,9501,9106,1207,6401,7105,4806,8401,5905,090 6,360 Vc =150 m/mi1,490 n,fz =5,960 0.8 mm/t7,1601,3605,4406,5301,1904,7605,7209503,8006,080
1,7403,1404,1801,5303,6804,5901,3603,2704,0801,2703,050 3,810 Vc =120 m/mi1,190 n,fz =3,570 0.6 mm/t4,2901,0903,2703,9309502,8503,4207602,2803,650
1,7402,6103,4801,5303,0603,8301,3602,7203,4001,2702,540 3,180 Vc =120 m/mi1,190 n,fz =2,980 0.5 mm/t3,5701,0902,7303,2709502,3802,8507601,9003,040
1,4501,7402,3201,2702,0402,5401,1401,8302,2801,0601,700 2,120 Vc =100 m/mi990 n,fz =1,980 0.4 mm/t2,3809101,8202,1908001,6001,9206401,2802,050
2,8908,67011,5602,55010,200 12,7502,2709,08011,3502,1208,480 10,600 Vc =200 m/m1,990 in,fz =9,950 1 mm/t11,9401,8209,10010,9201,5907,9509,5401,2706,35010,160
2,1706,5108,6801,9107,6409,5501,7106,8408,5501,5906,360 7,950 Vc =150 m/m1,490 in,fz =7,450 1 mm/t8,9401,3606,8008,1601,1905,9507,1409504,7507,600
5801,0501,4005101,2301,5304501,0801,3504201,010 1,260 Vc =40 m/min400 ,fz = 01,200 .6 mm/t1,4403601,0801,3003209601,1602507501,200
430390520380460570340410510320390 480 Vc =30 m/min300 ,fz = 0450 .3 mm/t540270410490240360440190290460
1,7401,5702,0901,5301,8402,3001,3601,6402,0401,2701,530 1,910 Vc =120 m/mi1,190 n,fz =1,790 0.3 mm/t2,1501,0901,6401,9709501,4301,7107601,1401,830
1,1601,0501,4001,0201,2301,5309101,1001,3708501,020 1,280 Vc = 80 m/min800 ,fz = 01,200 .3 mm/t1,4407301,1001,3206409601,1605107701,230
870530700760610760680550680640520 640 Vc = 60 m/min600 ,fz = 0600 .2 mm/t720550550660480480580380380610
- The above table shows the conditions for standard shank type cutters. When using- Cutting conditions are generally limited by the rigidity and power of the machine and the
long shank type cutters, the number of teeth may be different. In this case, the cuttingrigidity of the workpiece. When setting the conditions, start from half of the values of the
conditions should be changed by referring to: “The usage of standard and long shanks”standard cutting conditions and then increase the value gradually while making sure the
shown in previous pagemachine is running normally

APPLICATION R ANGE

APMX Shoulder milling SlotAPMX ting RampinRMPX Traversin gA g Small depth plungingPlungingDrilling (Helical feed)Enlarged hole
Wae
øD1, øD2
DesignationDCX Tool dia.APMX Max. depth of cutRMPX Max. ramping angleA Max. plunging depthW øD1 Max. cutting width in plunging Min.machinable hole dia.øD2 Max.machinable hole dia.ae Max. cutting width in enlarged hole
E/HXN03R016M...ø160.9Not possibleNot possible3.8 Not possibleNot possible12.2
E/HXN03R018M...ø180.91.7°0.273.8 263414.2
E/HXN03R020M...ø200.91.4°0.273.8 303816.2
E/HXN03R022M...ø220.91.2°0.273.8 344218.2
E/HXN03R025M...ø250.91°0.273.8 404821.2
E/HXN03R028M...ø280.90.8°0.273.8 465424.2
E/HXN03R030M...ø300.90.7°0.273.8 505826.2
E/HXN03R032M...ø320.90.7°0.273.8 546228.2
EXN03R035M...ø350.90.6°0.273.8 606831.2
E/H/TXN03R040M…ø400.90.5°0.273.8 707836.2
TXN03R050M...ø500.90.4°0.273.8 909846.2

・ For øDc above ø33 mm, slot milling, ramping or contouring is not recommended as chips may be re-cut