Общий каталог Sumitomo 2019 - 2020 - страница 447

ApplicationsFace MillingShoulder Milling / Semi-Shoulder Milling Shank Dia. (mm) 12.712.7M ±0.0137.510.5 IC IC12.70IC12.7012.7010.2 Axial Radial General–purpose Finishing Face Milling High Feed Shoulder Milling Groove Milling Ramping Chamfering Drilling Profiling Profile Finishing General Steel / Carbon Steel / Alloy Steel Tempered Steel / Die Steel Stainless Steel Cast Iron / Ductile Cast Iron Non–ferrous Metal Aluminum Alloy Ti Alloy / Heat–Resistant Alloy Hardened Steel MM ±0.013±0.013 High-speedCast IronNon-ferrousMetalChamferingGroove /T-SlotR / 3DProfilingRadiusMulti-PurposeHigh FeedShoulderMillingFace MillingMillingCutters G: Best S: Suitable H: Unsuitable Blank: Not Recommended Work Material Application P M K N S H Cutting Edge Angle Cutting Series Model Insert Rake / Edge Cat. No. Angle Maximum Depth of Cut Dia. / (mm) Diagram Cutting edge angle (Typical) 45 to 55 (Page) HRC * ø80 FPGto−ø315 SDKN42M (IC=12.70)FPG4000SDKN53M (IC=15.875)2.0 15° –4° S S* ø100 S S S S H to − FPG5000 15° –4° ø200 →H40 IC FPE SDKN42MT * ø50 ø32 2.0 to to FPE4000 15° –3° S S S S S S S ø80 ø42 →H41 12.70 * ø80 EHGto−ø200 SEKN42MT (IC=12.70)EHG4000SEKN53MT (IC=15.875)1.4 20° –3° * ø(80)to− EHG5000 M ±0.013 S S20° –3° S S S S S S ø(200) →H42 IC DNX SNMT1205ZNEN ø80to −ø250 DNX12000DNXF12000 –5° –6° S S S G →H46 12.7 DNH(S) SNMT1205ZNEN ø80to −ø160 DNH12000DNHS12000 –5° –6° S S S G →H47 12.7 DNF CSNH43M ø80 to − DNF4000 –5° –6° S S S S G H H H ø200 →H48 2.012.70 APG SDC(H)42TR 2.5 ø80 to − APG4000 18° –2° S S S S S S S G G H ø315 25° M±0.013 →H49 12.70 25° ø80 DPGto−ø200 SPCH42 (IC=12.70)DPG4000DPGF4000SPCH53 (IC=15.875)15° ±0.013 8° 0°M S S S S S S S S S ø100 to − DPG5000 8° 0° ø315 →H50 IC ø40to WEZ− (For 11000 Type)WEZ11000R(S) AOMT11T302PEER-G 14°to –7°to ø100 RE 15° –11° ø40 –10° –4° G G G G G G G G G G G G to − WEZ17000R(S) to to ø160 →H58 12.8 –15° –9° ø14to ø16 to WEZ–E WEZ11000E (For 17000 Type)AOMT170502PEER-G 6°to –7°to ø80 ø32 WEZ11000EL RE 15° –18° G G G G G G G G G G G G ø25 ø25 WEZ17000E 6° –6° to to to to ø80 ø42 →H62 WEZ17000EL 19.5 15° –12° ø32to − WEX–F/R (For 3000 Type) 9° 7°WEX1000FAXMT170508PEER–Gtoto ø63 17° 17° ø40 23° 16° to − WEX2000F to to S G G S G G G G G G G ø63 25° 18° ø40 WEX3000F RE 17.54 19° 12° to −ø125 →H75 WEX3000R WEXF3000R to to24° 15° *Use a chamfering tool for chamfering operations. H3