Общий каталог Sumitomo 2019 - 2020 - страница 446

Milling CuttersFace MillingShoulde rMillingHigh FeedMulti-PurposeRadiusR / 3DProfilingGroove /T-SlotChamferingNon-ferrousMetalHigh-speedCast Iron ApplicationsFace Milling Shank Dia. (mm) 13.413.49.52513.413.513.5IC12.70 Axial Radial General–purpose Finishing Face Milling High Feed Shoulder Milling Groove Milling Ramping Chamfering Drilling Profiling Profile Finishing General Steel / Carbon Steel / Aloy Steel Tempered Steel / Die Steel Stainless Steel Cast Iron / Ductile Cast Iron Non–ferrous Metal Aluminum Alloy Ti Alloy / Heat–Resistant Alloy Hardened Steel Cutter (Indexable Endmill) Selection Guide G: Best S: Suitable H: Unsuitable Blank: Not Recommended Work Material Application P M K N S H Cutting Edge Angle Cutting Series Model Insert Rake / Edge Cat. No. Angle Maximum Depth of Cut Dia. / (mm) Diagram Cutting edge angle (Typical) 45 to 55 (Page) HRC WGX SEMT13T3AGSR–G H * ø40to −ø250 WGX13000R(S) 2.0 20° –20°WGXM13000R(S)totoG G S G G G G G G SWGXF13000R(S)22° –24° →H20 13.4 WGX–EW SEMT13T3AGSR–G 2.0 * ø32 20° –20° to ø32 WGX13000EW to to G G S G G G G G G S ø63 22° –24° →H23 13.4 * ø32 WGCto−ø100 WGC3000 SEMT0903AGSN(3000 Type)WGC3000RS2.1 –10°20°to–19° G G S G G G G G G G * ø40to −ø200 WGC(F)4000→H24 WGC(F)4000RS 9.525 20° –20°toto22° –24° * ø20 ø20 WGC–EWtotoø63ø32 SEMT13T3AGSNWGC3000EW(4000 Type)2.5 –10°20°to–19° G G S G G G G G G G * ø32 20° –20° to ø32 WGC4000EW to to ø63 →H26 13.4 22° –24° * DGC SNMT13T6ANER–G ø40 DGC13000R(S) 1.8 * to ø250 − DGCM13000R(S) –5° –10° G S G G G G G G SDGCF13000R(S) →H32 13.5 * DGC–EW SNMT13T6ANER–G ø40 1.8 * toø63 ø32 DGC13000EW –5° –10° G S G G G G G G S →H35 13.5 * ø80 UFOto−ø250 SFKN12T3AZTN (IC=12.70)UFO4000SFKN1504AZTN (IC=15.875)2.2 27° –7° S S S S S S S S S S * ø100 to − UFO5000 27° –7° ø250 →H36 IC UFO–E SFKN12T3AZTN * ø50 ø32 2.2 to to UFO4000E 27° –7° S S S S S S S S S S ø80 ø42 12.70 →H38 GRC RGEN2004SN–S ø80 to − GRC6000 25° 10° S S S S G G G S ø160 →H39 ø20 ±0.025 *Use a chamfering tool for chamfering operations. ■ Precautions when Using Wiper Inserts with Holes Fig 1 Fig 2 ● When assembling the wiper insert, attach it as shown in Fig. 1. When attached as shown in Fig. 2, normal machined surface roughness cannot be obtained. ● The wiper insert has a single corner specification. ● Refer to page N19 of Technical Guidance for details about milling with wiper inserts. H2 MM ±0.013±0.013