Общий каталог Sumitomo 2019 - 2020 - страница 337

CW SAC830PAC830P AC425KAC520U AC520UAC530U AC530UT2500A CWT2500A S Pcs/PackPcs/Pack CW S AC830PAC830PH10AC830P AC425KAC425KAC520U AC520UAC520UAC530U CW AC530UAC530UAC1030U T2500AFront Cu ting Edge Angle S Pcs/PackPcs/PackPcs/PackPcs/Pack Tools Grooving SEC-Grooving Tools (for Small Lathes) GNDM / GNDL Type GNDM Type (For Small Lathes) / GNDL Type (For Small Lathes) Inserts  ( Coated Carbide / Cermet / Carbide) Fig 1 Fig 2 Fig 3 Fig. 4 (Figure shows a right-handed (R) tool.) 4-RE 2-RE 4-RE L L L PSI L 4-RE Grooving / Traverse Cutting  Dimensions (mm) External Profiling / External Radius Grooving  Dimensions (mm) F Appearance Cat. No. Width of CW Cut Nose Radius Overal Length Thickness Fig Appearance Cat. No. Width of CW Cut Nose Radius Overal Length Thickness Fig WidthofCut Tolerance RE L S Width of Cut Tolerance RE L S MG GCM N3004-MG ● ● ● ● Q 3.0 ±0.03 0.4 21.1 3.8 5 1 RG GCM N3015-RG ●●●●● 3.0 ±0.03 1.5 21.1 3.8 5 2 General-purpose General-purpose ML GCM N2002-MLN3002-MLQ Q ●● Q●●●●● 2.03.0±0.03 0.2 21.1 3.6±0.03 0.2 21.1 3.8 5 11 Profiling / Radius Grooving / Necking  Dimensions (mm) Low Feed Grooving / Cut-Off Machining  Appearance Cat. No.Dimensions (mm) Width of CW Cut Nose Radius Overal Length Thickness FigWidth of CutToleranceRELS Appearance Cat. No. Width of CW Cut Nose Radius Overal Length Thickness RNFig GCM N2010-RN Q Q ●●GCM N3015-RN●●●● 2.0 ±0.03 1.0 21.7 3.63.0±0.03 1.5 22.4 3.85 22 WidthofCut Tolerance RE L S General-purpose GG GCM N2002-GG ●●● Q 2.0 ±0.03 0.2 21.1 3.6 1 GCM N3002-GG ●●● Q 3.0 ±0.03 0.2 21.1 3.8 5 1 Non-Ferrous Metals  Dimensions (mm) General-purpose GCM N3004-GG ●●● Q 3.0 ±0.03 0.4 21.1 3.8 1GLGCM N2002-GL●●● QGCM N3002-GL●●● Q2.03.0±0.03 0.221.1 3.6±0.03 0.221.1 3.8511AppearanceCat. No.Width of CW Cut Nose Radius Overal Length Thickness FigWidth of CutToleranceRELS Low FeedGF GCM N125005-GF Q Q ● QGCM N150005-GFQQ●QGCM N2002-GFQ●●1.25 ±0.03 0.05 17.4 3.2 11.52.0±0.03 0.05 17.4 3.7±0.03 0.221.1 3.6511GAGCG N2002-GA●GCG N3002-GA●General-purpose 2.03.0 ±0.025 0.2 21.1 3.6±0.025 0.2 21.1 3.8 5 33 Low Resistance N3002-GF ●●●● 3.0 ±0.03 0.2 21.1 3.8 1 Cut-Off (Handed Edge)  Dimensions (mm) Appearance Cat. No. Width of CW Cut Nose Radius Overal Length Thickness Fig PSI Width of Cut Tolerance RE L S CG GCM R2002-CG-05 ●●● Q 5˚ 2.0 ±0.03 0.2 21.1 3.6 4 GCM L2002-CG-05GCM R3002-CG-05●●● Q 5˚●●●Q5˚ 2.03.0 ±0.03 0.2±0.03 0.221.1 3.621.3 3.8 5 44 General-purpose GCM L3002-CG-05 ●●● Q 5˚ 3.0 ±0.03 0.2 21.3 3.8 4 CF GCM R20003-CF-10 Q Q Q ● 10˚ 2.0 ±0.08 0.03 22.4 3.6 4 GCM L20003-CF-10 Q Q Q ● 10˚ 2.0 ±0.08 0.03 22.4 3.6 4 GCM R30003-CF-10 Q Q Q ● 10˚ 3.0 ±0.08 0.03 22.4 3.8 4 GCM L30003-CF-10GCM R20003-CF-15QQQQQ ● 10˚Q● 15˚ 3.02.0 ±0.08 0.03 22.4 3.8±0.08 0.03 22.4 3.6 5 44 GCM L20003-CF-15 Q Q Q ● 15˚ 2.0 ±0.08 0.03 22.4 3.6 4 GCM R30003-CF-15 Q Q Q ● 15˚ 3.0 ±0.08 0.03 22.4 3.8 4 Low Resistance GCM L30003-CF-15 Q Q Q ● 15˚ 3.0 ±0.08 0.03 22.4 3.8 4 GCMR: Right Handed, GCML: Left Handed Combine the insert with a holder such that the width of cut (CW) matches. Not usable with GNDIS type holders. Recommended Cutting Conditions F21 ● mark: Standard stocked item (new product/expanded item) F23