Общий каталог Sumitomo 2018 - 2019 - страница 546
Навигация
Общий каталог Sumitomo 2012
Каталог Sumitomo резьбонарезной инструмент
Каталог Sumitomo пластины с режущей кромкой-моноалмаз Sumicristal
Каталог Sumitomo инструмент для обработки канавок
Общий каталог Sumitomo 2019 - 2020
Каталог Sumitomo запасные части- Pages 3-6_CS6_EN_web
- A 1-20 insert selection EN_web
- B 1-14 grades_EN_web
- C01-17 inserts intro pages_EN_web
- C18-56 negative inserts_EN_web
- C57-86 positive inserts_EN_web
- D 1-46 tool holders_EN_web
- E 1-24 boring bars_EN_web
- F 1-48 grooving_thread tools_EN_web
- G 1-54 milling cutters_EN_web
- H 1-48 insert type endmills_EN_web
- J 1-24 new endmills_EN_web
- J 25-50 endmills_EN_web
- K 1-46 Multi-Drills_EN_web
- K 47-76 Multi-Drills_EN_web
- L 1-28 cbn_pcd grades_EN_web
- M 1-34 cbn_pcd inserts_EN_web
- M 35-56 SHM tools_EN_web
- N1-24 technical guidance_EN_web
- P 1-8 spare parts_neu_EN_web
- P 9-22 index_notes_EN_web
SRF Type
High Speed Finishing of Aluminium Alloy
Fig. 1 Fig. 2
Body Spare Parts
Adjustment screw Torque wrench
| Cat. No. | Stock | øD(mm) | No. of teeth | Fig. | Weight (Kg) |
| SRF 30 R-ST | q | 30 | 3 | 1 | 0,34 |
| SRF 40 R-ST | q | 40 | 4 | 1 | 0,50 |
| SRF 50 RS | q | 50 | 5 | 2 | 0,59 |
| SRF 63 RS | q | 63 | 6 | 2 | 0,67 |
Insert screw Hex wrench
Inserts are sold seperately.
Wrench Insert 1,8 x 45
Maximum D.O.C. Guide (SRF50RS, 5 teeth)
The contains guidelines on the maximum D.O.C., determined from internal tests. ”O” mark indicates the possible application range. Actual cutting conditions should be set, based on actual machine and work characteristics.
Fig. 1 Fig. 2 Fig. 3
Cutting SUMIDIA Feed Speed, v (mm/min)
| Fig | Feed | f | ||
| Cat. No. | Edge |
DA2200 2.500 4.000 5.000
| SNEW 09T3 ADTR-NF | Standard | 1 | Feed Rate, f (mm/tooth) D.O.C. | |
| s | t | |||
| SNEW 09T3 ADTR-U-NF | Wiper | 2 | 0,10 0,08 0,05 (mm) | |
| s | ||||
| SNEW 09T3 ADTR-R-NF | 0,5 | |||
| Nose Radius | s | 3 |
1,0 1,5 2,0 l Standard inserts and Wiper inserts can be used on the same cutter body.
2,5 Standard inserts with nose radius should be used where vibration is 3,0 l
| present. As such, Wiper-inserts will not be appliccable. | 3,5 | – | |||
| 4,0 | – | – | |||
| l Inserts can be regrind 3 times (up to minimum IC diameter 9,225mm). | 4,5 | – | – | ||
| 5,0 | – | – | |||
| l When using reground inserts, it is advisable to reconfirm insert height and | |||||
| cutting diameter with a tool pre-setter. | l Cutting Conditions | ||||
| Cutter: | SRF 50 RS | ||||
| l Do not mix new and reground inserts, or even inserts with different regrind | Insert: | SNEW 09T3 ADFR-NF (DA2200) | |||
| amount on the same cutter. | n : | 10.000 rpm |
Width: 35mm at D.O.C. indicated above Recommended Cutting Conditions for RF and SRF Type Cutters
| Work Mate | rial | Process | Grade | CuttingSpee RFType | d(m/min) SRFType | Feed Rate (mm /tooth) | RFType Depth of | SRFType Cut(mm) |
| Si < 13% | Finishing | DA2200(PCD) | 2.000 ~ 5.000 | ~ 4.000 | ||||
| Aluminium Alloy | Si≥13% | Roughing Finishing | H1(Carbide) DA2200(PCD) | 1.000 ~ 2.500 400 ~ 800 | – ~ 800 | 0,05 ~ 0,2 | ~ 3,0 | ~ 5,0 |
| Roughing | H1(Carbide) | 200 ~ 400 | – |