Заказ инструмента: http://steelcam.org | 8 (343) 382-52-03 | [email protected] 80.0VXE92-_R-16 Face Milling Cutter Assemblies d1 H Cartridge Face Mills Product Dimensions (mm) Spares D D Screw Da EDP Item Description Effective Da* H d1 ap No. of EDP EDP Tightening Cutting max Teeth Nm Diameter 8000VXE92-_ R-16 Bodies with Unequal Medium Pitch & Cartridges 033207 8000VXE92-100R-16 82,15 106 68 32 3,5 6 033208 8000VXE92-125R-16 107,15 131 63 40 3,5 8 033209 8000VXE92-160R-16 142,15 166 63 40 3,5 10 031225 DP5013T 030819 TP20 6,10 033210 8000VXE92-200R-16 182,15 206 63 60 3,5 12 033211 8000VXE92-250R-16 232,15 256 63 60 3,5 16 8010VXE92-_ R-16 Bodies with Equal Medium Pitch & Cartridges 033212 8010VXE92-100R-16** 82,15 106 68 32 3,5 6 033213 8010VXE92-125R-16** 107,15 131 63 40 3,5 8 031225 DP5013T 030819 TP20 6,10 Cutter Body & Cartridges 033214 8010VXE92-160R-16** 142,15 166 63 40 3,5 10 033215 8010VXE92-200R-16** 182,15 206 63 60 3,5 12 ** Denotes non stock items. Da* = Outside Diameter Product Spares Screw Cartridge Adjustment EDP Item Description EDP EDP Tightening Screw Screw Nm EDP EDP Cartridge & Spares 031308 80VX92R-16 031225 DP5013T 030819 TP20 6,10 022646 7065 - - 80VX92R-16 Note: Mounting instructions refer to pages A161 - A164. Note: XE..1605.., X-Style cutter assemblies cannot utilise the finishing wiper cartridges. 80.0VXE92-_R-16 Technical Information (mm) Product Dimensions Ramping ap max Ramping Helical EDP Item Description Facing Angle Helical Hole Helical / Max Interpolation Pitch A° B° min. - max. Linear RPM Flat 033207 8000VXE92-100R-16 82,15 0.39 0.47 186 210 2,50 10800 033208 8000VXE92-125R-16 107,15 0.29 0.36 236 260 2,50 9200 033209 8000VXE92-160R-16 142,15 0.22 0.27 306 330 2,50 7800 033210 8000VXE92-200R-16 182,15 0.17 0.20 386 410 2,50 6800 Facing Pitch 033211 8000VXE92-250R-16 232,15 0.13 0.16 486 510 2,50 5900 033212 8010VXE92-100R-16** 82,15 0.39 0.47 186 210 2,50 10800 Ramp angle A uses one outside cutting edge only. 033213 8010VXE92-125R-16** 107,15 0.29 0.36 236 260 2,50 9200 Ramp angle B uses 033214 8010VXE92-160R-16** 142,15 0.22 0.27 306 330 2,50 7800 two cutting edges 033215 8010VXE92-200R-16** 182,15 0.17 0.20 386 410 2,50 6800 (one outside and ** Denotes non stock items. one inside edge). A B ap D A = max ramp angle utilizing full face contact Da* B = max ramp angle utilizing full contact + internal corner radius Depth of Cut (ap) A120 www.kennametal.com