Каталог Stellram фрез со сменными пластинами - страница 120

Предыдущая страница Следующая страница

Навигация

80.0VXD92-_R-12

XDLW12-D XDLT12-D41 XDLT12-D721 XDLT12-D411d l
ProductApplication & MaterialDimensions (mm)ills
FacingSlottingPlungings e M
EDPItem DescriptionGradeDepth of Cut(mm)d (IC)lsrhmminr ac
apmax. 2,50apmax. 2,00aemax. 9,00ge F
029490XDLW120508SR-DX40012,7012,705,560,800,10trid
029488XDLW120508SR-DX50012,7012,705,560,800,10Car
029489XDLW120508SR-DSC302512,7012,705,560,800,10
029682XDLT120508ER-D41X50012,7012,705,560,800,05
031534XDLT120508ER-D41SP651912,7012,705,560,800,05
033068XDLT120508ER-D41SC652512,7012,705,560,800,05
029638XDLT120508ER-D721GH212,7012,705,560,800,04
030783XDLT120512ER-D411X50012,7012,705,561,200,05
030792XDLT120512ER-D411SP651912,7012,705,561,200,05

Machining Choice: 1st Choice 2nd Choice 3rd Choice | Material Guide Key descriptions found on page A5. XDLW120508SR-D X500 should be used for Alloyed Steel and Stainless Steel with heavy scale. XDLT120512ER-D411 is a more positive geometry than the -D41 with a larger radius which increases performance during smaller radial engagements or where chipping may occur when using the -D41 geometry. XDLT120512ER-D411 uses less power than -D41.

80.0VXD92_R12 Feeds fz (mm/tooth)

GeometryGradeOperationUnalloyed SteelAlloyed SteelStainless SteelStainless Steel Refractory PHGray IronSpheroidal- Ductile IronMalleable IronAluminium & AlloysAluminium & Silicon >16% Si 92 HBNHTA Iron Based AlloysHTA Cobalt Based AlloysHTA Nickel Based AlloysHTA Titanium Based AlloysHard Steel >1400 N/mm2 >415 HBNChilled Cast Iron >1400 N/mm2
Min. - Max.Min. - Max.Min. - Max.Min. - Max.Min. - Max.Min. - Max.Min. - Max.Min. - Max.Min. - Max.Min. - Max.Min. - Max.Min. - Max.Min. - Max.Min. - Max.Min. - Max.
SR-DX400Facing0,30 - 2,700,30 - 2,50-----------0,30 - 1,200,30 - 1,50
SR-DX400Slotting0,30 - 2,500,30 - 2,40-----------0,30 - 0,800,30 - 1,00
SR-DX500Facing-0,30- 2,500,20- 1,700,20-1,20-----------
SR-DX500Slotting-0,30- 2,400,20- 1,500,20- 1,00-----------
SR-DSC3025Facing----0,30 - 3,000,30 - 2,800,30 - 2,50--------
SR-DSC3025Slotting----0,30 - 2,500,30 - 2,300,30 - 2,10--------
ER-D41X500Facing--0,20 - 1,400,20 - 0,90-----0,20 - 0,850,20 - 0,850,20 - 0,850,20 - 1,00--
ER-D41X500Slotting--0,20 - 1,100,20 - 0,80-----0,10 - 0,700,10 - 0,700,10 - 0,700,10 - 0,80--
ER-D41SP6519Facing0,30 - 2,500,30 - 2,300,20 - 1,200,20 - 0,750,30 - 2,500,30 - 2,30---0,20 - 0,850,20 - 0,850,20 - 0,850,20 - 1,00--
ER-D41SP6519Slotting0,30 - 2,000,30 - 1,800,20 - 1,000,15 - 0,600,30 - 2,000,30 - 1,80---0,10 - 0,700,10 - 0,700,10 - 0,700,10 - 0,80--
ER-D41SC6525Facing0,20 - 2,000,20 - 1,65--0,30 - 2,500,30 - 2,30---------
ER-D41SC6525Slotting0,20 - 1,750,20 - 1,55--0,30 - 2,000,30 - 1,80---------
ER-D721GH2Facing-------0,30 - 1,500,30 - 1,50------
ER-D721GH2Slotting-------0,30 - 1,500,30 - 1,50------
ER-D411X500Facing--0,20 - 1,400,20 - 0,90-----0,20 - 0,850,20 - 0,850,20 - 0,850,20 - 1,00--
ER-D411X500Slotting--0,20 - 1,100,20 - 0,80-----0,10 - 0,700,10 - 0,700,10 - 0,700,10 - 0,80--
ER-D411SP6519Facing0,30 - 2,500,30 - 2,300,20 - 1,200,20 - 0,750,30 - 2,500,30 - 2,30---0,20 - 0,850,20 - 0,850,20 - 0,850,20 - 1,00--
ER-D411SP6519Slotting0,30 - 2,000,30 - 1,800,20 - 1,000,15 - 0,600,30 - 2,000,30 - 1,80---0,10 - 0,700,10 - 0,700,10 - 0,700,10 - 0,80--

Note: HTA = High Temperature Alloys Speed recommendations can be found on page A122.