Общий каталог SGS 2021 - страница 49

FRACTIONAL Z-Carb ADVANCED PRODUCTIVITY 38° 35° 4 ≠ ≠ LF DC APMX DCON Z1 • RE Z16CR FRACTIONAL SERIES TOLERANCES (inch) inch EDP NO. • Variable rake geometry 1/8–1/4 DIAMETER CUTTING LENGTH OVERALL SHANK CORNER Ti-NAMITE-X Ti-NAMITE-X JetStream alters and controls the DIAMETER OF CUT LENGTH DIAMETER RADIUS W/FLAT cutting dynamic taking DC = +0.0000/–0.0012 DC APMX LF DCON RE chatter suppression to DCON = h 6 an unprecedented level RE = +0.000/–0.002 1/8 1/4 1-1/2 1/8 .015 36505 – – • Unequal helix design 1/8 3/8 1-1/2 1/8 – 36404 – – reduces damaging >1/4–3/8 DIAMETER harmonics by changing DC = +0.0000/–0.0016 5/32 5/16 2 3/16 .015 36506 – – the angle at which each DCON = h 6 5/32 7/16 2 3/16 – 36406 – – cutting edge enters and RE = +0.000/–0.002 3/16 3/8 2 3/16 .015 36507 – – exits the material • Unequal flute spacing >3/8–3/4 DIAMETER 3/16 7/16 2 3/16 – 36408 – – helps to disrupt the DC = +0.0000/–0.0020 7/32 3/8 2 1/4 .020 36508 – – rhythmic pattern DCON = h 6 created by the cutting 1/4 1/2 2-1/2 1/4 – 36416 – – edge helping to RE = +0.000/–0.002 suppress damaging 1/4 7/16 2 1/4 .020 36509 – – harmonics 1/4 3/4 2-1/2 1/4 – 36596 – – • Optimal material STEELS 9/32 5/8 2-1/2 5/16 – 36418 – – removal rates through increased feed and STAINLESS STEELS 5/16 1/2 2 5/16 .020 36511 – – depths of cut CAST IRON 5/16 13/16 2-1/2 5/16 – 36420 – – • Enhanced corner 11/32 13/16 2-1/2 3/8 – 36422 – – geometry with tight HIGH TEMP ALLOYS tolerance corner radii 3/8 5/8 2 3/8 .020 36513 – – • Recommended for TITANIUM 3/8 7/8 2-1/2 3/8 – 36424 36530 – materials ≤ 45 HRc (≤ 420 Bhn) HARDENED STEELS 13/32 15/16 2-3/4 7/16 – 36426 36531 – 7/16 5/8 2-1/2 7/16 .020 36515 – – For patent 7/16 1 2-3/4 7/16 – 36428 36532 – information visit 15/32 1 3 1/2 – 36430 36533 – www.ksptpatents.com 1/2 5/8 2-1/2 1/2 .030 36517 – – 1/2 1 3 1/2 – 36432 36534 36826 1/2 1-1/4 3-1/4 1/2 – 36597 36598 – 9/16 1-1/8 3-1/2 9/16 – 36436 36535 36827 5/8 3/4 3 5/8 .040 36519 – – 5/8 1-1/4 3-1/2 5/8 – 36440 36536 36828 3/4 1 3 3/4 .040 36520 – – 3/4 1-1/2 4 3/4 – 36442 36537 36829 1 1-1/2 4 1 – 36444 36538 36830 Refer to page 43 for speed & feed recommendations 49 END MILLS www.kyocera-sgstool.com END MILLS