Общий каталог SGS 2021 - страница 39

FRACTIONAL Z-Carb-AP 38° 35° 4 ≠ ≠ LF APMX DC DCON RE Z1PCR FRACTIONAL SERIES TOLERANCES (inch) inch EDP NO. • Variable rake geometry <1/8 DIAMETER CUTTING LENGTH OVERALL SHANK CORNER Ti-NAMITE-X Ti-NAMITE-X JetStream alters and controls the DIAMETER OF CUT LENGTH DIAMETER RADIUS W/FLAT cutting dynamic taking DC = +0.0005/–0.0005 DC APMX LF DCON RE chatter suppression to DCON = h 6 an unprecedented level 1/64 1/32 1-1/2 1/8 .002 36874* – – RE = +0.000/–0.0010 • Unequal helix design 1/32 5/64 1-1/2 1/8 .005 36875* – – changes the cutting 1/8–1/4 DIAMETER angle to improve 3/64 7/64 1-1/2 1/8 .005 36876* – – DC = +0.000/–0.0012 harmonics DCON = h 6 1/16 3/16 1-1/2 1/8 .005 36872* – – • Unequal flute spacing RE = +0.000/–0.0020 5/64 3/16 1-1/2 1/8 .005 36877* – – helps to disrupt the rhythmic pattern >1/4–3/8 DIAMETER 3/32 9/32 1-1/2 1/8 .010 36873* – – created by the cutting 7/64 3/8 1-1/2 1/8 .010 36878* – – edge helping to DC = +0.000/–0.0016 suppress damaging DCON = h 6 1/8 3/8 1-1/2 1/8 .010 36370 – – harmonics RE = +0.000/–0.0020 1/8 3/8 1-1/2 1/8 .015 36851 – – • Enhanced corner geometry with tight >3/8–1 DIAMETER 3/16 7/16 2 3/16 .010 36371 – – tolerance corner radii DC = +0.000/–0.0020 3/16 7/16 2 3/16 .015 36852 – – • Recommended for DCON = h 6 materials ≤ 45 HRc 3/16 7/16 2 3/16 .030 36722 – – (≤ 420 Bhn) RE = +0.000/–0.0020 1/4 1/2 2-1/2 1/4 .010 36372 – – 1/4 1/2 2-1/2 1/4 .015 36723 – – STEELS 1/4 1/2 2-1/2 1/4 .020 36853 – – STAINLESS STEELS 1/4 1/2 2-1/2 1/4 .030 36373 – – 1/4 3/4 2-1/2 1/4 .010 36599 – – CAST IRON 1/4 3/4 2-1/2 1/4 .015 36600 – – HIGH TEMP ALLOYS 1/4 3/4 2-1/2 1/4 .020 36854 – – TITANIUM 1/4 3/4 2-1/2 1/4 .030 36601 – – HARDENED STEELS 5/16 13/16 2-1/2 5/16 .015 36724 – – 5/16 13/16 2-1/2 5/16 .020 36855 – – For patent 5/16 13/16 2-1/2 5/16 .030 36374 – – information visit 3/8 7/8 2-1/2 3/8 .010 36375 36701 – www.ksptpatents.com 3/8 7/8 2-1/2 3/8 .015 36725 36736 – 3/8 7/8 2-1/2 3/8 .020 36856 36864 – 3/8 7/8 2-1/2 3/8 .030 36376 36702 – 3/8 7/8 2-1/2 3/8 .060 36727 36738 – 7/16 1 2-3/4 7/16 .020 36857 36865 – 1/2 1 3 1/2 .010 36378 36704 36804 1/2 1 3 1/2 .015 36729 36740 36810 1/2 1 3 1/2 .030 36858 36866 36805 1/2 1 3 1/2 .060 36380 36706 36811 1/2 1 3 1/2 .090 36381 36707 36812 *Variable flute spacing. Helix and rake do not vary. continued on next page 39 END MILLS www.kyocera-sgstool.com END MILLS