Каталог SGS микро инструмент 2021 - страница 95
Навигация
Каталог SGS фрезы для алюминия S-carb
Каталог SGS монолитный инструмент из композитных материалов
Каталог SGS инструмент для обработки алюминия
Общий каталог SGS 2018
Общий каталог SGS 2021
Каталог SGS фрезы для труднообрабатываемых материалов Series 33
Speeds and Feeds
Instructions:
- rpm = use speed from INCH or METRIC Baseline chart
- ipm = INCH Baseline Feed (ipm) x Feed Multiplier [from selected chart below]
- mm/min = METRIC Baseline Feed (mm/min) x Feed Multiplier [from selected chart below]
- Reduce speed and feed 30 percent when using uncoated tools
- Find Width of Cut (Ae) and Depth of Cut (Ap) recommendations on chart below
- refer to the KYOCERA SGS Tool Wizard® or sgsmicrotools.com for detailed technical charts by series
Ap
Ae Ae
| Flute Length | 8 x | DC | 12 | x DC | |||||||
| INCH | Feed Multiplier | 0 . | .6 | . | 0 .5 | ||||||
| 2-Flute Square & Ball With Reach | Width/Depth Diameter (DC) | Ae x DC ≤0 .0312 | Ap x DC >0 .0312 | Ae x DC ≤0 .0312 | Ap x DC >0 .0312 | ||||||
| P | |||||||||||
| H K | Profile | ≤.25 ≤.50 | ≤.30 | ≤.22 ≤.45 | ≤.25 | ||||||
| ALL M | |||||||||||
| S N | Slot | 1 | ≤.07 ≤.17 | 1 | ≤.06 ≤.15 | ||||||
| INCH | Flute Length | 3 x DC . | 5 x . | DC . | 8 x DC . | 12 x DC . | 15 x DC . | 20 x . | DC . | 25 x . | DC . |
| 3-Flute | Feed Multiplier | 1 .4 | 1 . | .15 | 0 .9 | 0 .7 | 0 .6 | 0 . | .45 | 0 . | .35 |
| Square, Corner Radius & Ball | Width/Depth A | exDCApx | DC Ae x DC | ApxDCA | exDCApxDC | Ae x DC Ap x DC | Ae x DC Ap x DC | Ae x DC | Ap x DC | Ap x DC | Ap x DC |
| With Reach | Diameter (DC) ≤ . | 0 .0312 >0 .03 | .12 ≤0 .0312 | >0 .0312 ≤0 . | .0312 >0 .0312 | ≤0 .0312 >0 .0312 | ≤0 .0312 >0 .0312 | ≤0 .0312 | >0 .0312 | ≤0 .0312 | >0 .0312 |
| P ALL H K | Profile ≤. | 30 ≤.60 ≤.5 | ≤.30 ≤.60 | ≤.35 ≤.2 | 5 ≤.50 ≤.30 | ≤.22 ≤.45 ≤.25 | ≤.15 ≤.30 ≤.25 | ≤.12 ≤.25 | ≤.20 | ≤.12 ≤.25 | ≤.20 |
| M S N | Slot | 1 ≤.15 ≤ | .30 1 | ≤.08 ≤.20 | 1 ≤.07 ≤.17 | 1 ≤.06 ≤.15 | 1 ≤.06 ≤.15 | 1 | ≤.04 ≤.10 | 1 | ≤.04 ≤.10 |
| Flute Length | 8 x | DC | 12 | x DC | |||||||
| INCH | Feed Multiplier | 0 . | .95 | 0 . | .75 | ||||||
| 4-Flute Square & Ball | Width/Depth | Ae x DC | Ap x DC | Ae x DC | Ap x DC | ||||||
| With Reach | Diameter (DC) | ≤0 .0312 | >0 .0312 | ≤0 .0312 | >0 .0312 | ||||||
| P H K | Profile | ≤.25 ≤.50 | ≤.30 | ≤.22 ≤.45 | ≤.25 | ||||||
| ALL M | |||||||||||
| S N | Slot | 1 | ≤.07 ≤.17 | 1 | ≤.06 ≤.15 |
Note:
- Bhn (Brinell) HRc (Rockwell C)
- reduce speed and feed 30 percent when using uncoated tools
- Fz x No. of Flutes x max available rpm when recommendation exceeds machine limit
- helical ramp at 1 degrees or less, using slotting speed and feed rates (plunging is not recommended)
- reduce speed and feed for materials harder than listed
- reduce feed and Ae when finish milling (.02 x DC maximum)
- refer to the KYOCERA SGS Tool Wizard® or sgsmicrotools.com for detailed technical charts by series