Каталог SGS фрезы для алюминия S-carb - страница 6

Предыдущая страница Следующая страница

Навигация

Fractional & Metric | Speed & Feed Recommendations

Series S-Carb APRAeAp AeVcDiameter (D1) (inch)
FractionalAe x D1Ap x D1(sfm)3/4 1
Slot3280RPM16706 12530
1≤ 1(2624-3936)Fz0.0060 0.0070
Feed (IPM)301 263
ALUMINUM ALLOYSSlot >67hp4920RPM25059 18794
N 2024, 5052, 5086, 6061, 6063,1≤ 1Fz0.0090 0.0110
7075(3936-5904)Feed (IPM)677 620
Profile6560RPM33412 25059
≤ 0.5≤ 1.5Fz0.0090 0.0110
(5248-7872)Feed (IPM)902 827
Slot2620RPM13345 10008
1≤ 1(2096-3144)Fz0.0060 0.0070
Feed (IPM)240 210
ALUMINUM ALLOYSSlot >67hp3940RPM20068 15051
N (LITHIUM) 2090, 2091, 2099, 2195, 2199,1≤ 1(3152-4728)Fz0.0090 0.0110
2297, 8090Feed (IPM)542 497
Profile4920RPM25059 18794
≤ 0.5≤ 1.5Fz0.0090 0.0110
(3936-5904)Feed (IPM)677 620

Note: maximum recommended depths shown

  • surface speed is dependent on machine spindle & fixturing*
  • reduce speed and feed for materials harder than listed
  • balancing is recommended at ultra high surface speeds
  • ramp angle = 15˚ (feed rate = 30%)
  • tool life may be reduced when machining Lithium Alloys
  • maximum ramp depth = 1 x D

1

  • rpm = sfm x 3.82 / D
  • plunge depth = 1 x D (feed rate = 30%)

1 1

  • ipm = (inch / flute) x number of flutes x rpm
  • refer to the SGS Tool Wizard for complete technical information (www.sgstool.com)
Series S-Carb APRAeAp AeVcDiame (mter (D1) m)
MetricAe x D1Ap x D1(m/min)12162025
Slot1000RPM26525198941591512732
11Fz0.0800.1100.1500.180
(800-1200)Feed (mm/min)6366656571626875
ALUMINUM ALLOYSSlot >50kW1500RPM39788298412387319098
N 2024, 5052, 5086, 6061, 6063,1≤ 1Fz0.1200.1600.2200.270
7075(1200-1800)Feed (mm/min)14324143241575615469
Profile2000RPM53050397883183025464
≤ 0.5≤ 1.5Fz0.1200.1600.2200.270
(1600-2400)Feed (mm/min)19098190982100820626
Slot800RPM21220159151273210186
1≤ 1Fz0.0800.1100.1500.180
(640-960)Feed (mm/min)5093525257295500
ALUMINUM ALLOYSSlot >50kW1200RPM31830238731909815278
N (LITHIUM) 2090 2091 2099 2195 21991≤ 1Fz0.1200.1600.2200.270
, , , , , 2297, 8090(960-1440)Feed (mm/min)11459114591260512375
Profile1500RPM39788298412387319098
≤ 0.5≤ 1.5Fz0.1200.1600.2200.270
(1200-1800)Feed (mm/min)14324143241575615469

Note: maximum recommended depths shown

  • surface speed is dependent on machine spindle & fixturing*
  • reduce speed and feed for materials harder than listed
  • balancing is recommended at ultra high surface speeds
  • ramp angle = 15˚ (feed rate = 30%)
  • tool life may be reduced when machining Lithium Alloys
  • maximum ramp depth = 1 x D1
  • rpm = (1000 x m/min) / (3.14 x D1)
  • plunge depth = 1 x D1 (feed rate = 30%)
  • mm/min = (mm / flute) x rpm
  • refer to the SGS Tool Wizard for complete technical information (www.sgstool.com)