Каталог Mitsubishi Materials пластины для точения - страница 71
Навигация
Каталог Mitsubishi Materials отрезной и канавочный инструмент
Каталог Mitsubishi Materials запасные части
Каталог Mitsubishi Materials расточной инструмент
Каталог Mitsubishi Materials токарный инструмент для наружного точения
Общий каталог Mitsubishi 2020 - 2021
Каталог Mitsubishi Materials вращающийся инструмент 
ПЛАСТИНЫ ДЛЯ ТОЧЕНИЯ
РЕКОМЕНДУЕМЫЕ РЕЖИМЫ РЕЗАНИЯ
Отрицательная пластина
Стружколом: Std — стандарт; Flat — плоский верх.
P — Обрабатываемый материал: малоуглеродистая сталь (< 180HB, St37-2, Ck10)
| Режим резания | Приоритет | Стружколом | Покрытие | Скорость резания (м/мин) | Подача (мм/об) | Глубина резания (мм) |
|---|---|---|---|---|---|---|
| F | 1 | FY | VP25N | 285–445 | 0.09–0.23 | 0.20–0.80 |
| F | 2 | FS | NX2525 | 270–385 | 0.09–0.23 | 0.20–0.70 |
| L | 1 | SY | VP25N | 260–405 | 0.16–0.33 | 0.50–1.20 |
| F | 1 | FY | MP3025 | 275–420 | 0.09–0.23 | 0.20–0.80 |
| F | 2 | FY | NX3035 | 260–370 | 0.09–0.23 | 0.20–0.80 |
| F | 3 | FS | NX2525 | 270–385 | 0.09–0.23 | 0.20–0.70 |
| L | 1 | SY | MP3025 | 250–385 | 0.16–0.33 | 0.50–1.20 |
| L | 2 | SY | NX3035 | 235–335 | 0.16–0.33 | 0.50–1.20 |
| F | 1 | FY | UE6020 | 285–460 | 0.09–0.23 | 0.20–0.80 |
| F | 2 | FS | UE6020 | 285–460 | 0.09–0.23 | 0.20–0.70 |
| L | 1 | SY | UE6020 | 260–420 | 0.16–0.33 | 0.50–1.20 |
| F | 1 | FH | AP25N | 215–340 | 0.08–0.20 | 0.20–1.00 |
| F | 2 | FH | NX2525 | 205–295 | 0.08–0.20 | 0.20–1.00 |
| F | 3 | R/L-F | MP3025 | 210–325 | 0.05–0.15 | 0.10–0.50 |
| F | 4 | PK | NX2525 | 195–280 | 0.10–0.30 | 0.20–1.00 |
| L | 1 | LP | UE6105 | 220–405 | 0.10–0.40 | 0.30–2.00 |
| L | 2 | SH | UE6105 | 220–405 | 0.10–0.40 | 0.30–2.00 |
| L | 3 | LP | MP3025 | 195–295 | 0.10–0.40 | 0.30–2.00 |
| L | 4 | SH | AP25N | 200–315 | 0.10–0.40 | 0.30–2.00 |
| L | 5 | SH | NX2525 | 190–270 | 0.10–0.40 | 0.30–2.00 |
| L | 6 | SA | UE6105 | 220–405 | 0.10–0.40 | 0.30–2.00 |
| L | 7 | SW | UE6105 | 220–405 | 0.10–0.50 | 0.30–2.50 |
| L | 8 | SW | MP3025 | 195–295 | 0.10–0.50 | 0.30–2.50 |
| L | 9 | SW | NX2525 | 190–270 | 0.10–0.50 | 0.30–2.50 |
| L | 10 | R/L-K | MP3025 | 195–295 | 0.08–0.20 | 0.30–1.20 |
| M | 1 | MP | UE6105 | 200–370 | 0.16–0.50 | 0.30–4.00 |
| M | 2 | MP | MP3025 | 175–270 | 0.16–0.50 | 0.30–4.00 |
| M | 3 | MA | UE6105 | 200–370 | 0.20–0.50 | 0.30–4.00 |
| M | 4 | MH | UE6105 | 200–370 | 0.20–0.55 | 1.00–4.00 |
P — Обрабатываемый материал: углеродистая сталь • легированная сталь (180–280HB, Ck45, 42CrMo4)
| Режим резания | Приоритет | Стружколом | Покрытие | Скорость резания (м/мин) | Подача (мм/об) | Глубина резания (мм) |
|---|---|---|---|---|---|---|
| M | 5 | Std | UE6105 | 200–370 | 0.25–0.60 | 1.50–5.00 |
| M | 6 | Std | MP3025 | 175–270 | 0.25–0.60 | 1.50–5.00 |
| M | 7 | Std | NX2525 | 170–245 | 0.25–0.60 | 1.50–5.00 |
| M | 8 | Std | UTi20T | 85–125 | 0.25–0.60 | 1.50–5.00 |
| M | 9 | MW | UE6105 | 200–370 | 0.20–0.60 | 0.90–4.00 |
| M | 10 | R/L | MP3025 | 175–270 | 0.15–0.32 | 0.40–2.00 |
| R | 1 | RP | UE6105 | 190–350 | 0.25–0.60 | 1.50–6.00 |
| R | 2 | GH | UE6105 | 190–350 | 0.25–0.60 | 1.50–6.00 |
| H | 1 | HX | UE6110 | 160–275 | 0.50–1.26 | 3.00–11.00 |
| H | 2 | HV | UE6110 | 135–225 | 0.70–1.30 | 4.00–12.00 |
| F | 1 | FH | MP3025 | 210–325 | 0.08–0.20 | 0.20–1.00 |
| F | 2 | FH | NX3035 | 200–285 | 0.08–0.20 | 0.20–1.00 |
| F | 3 | FH | UE6110 | 230–390 | 0.08–0.20 | 0.20–1.00 |
| L | 1 | LP | UE6110 | 210–355 | 0.10–0.40 | 0.30–2.00 |
| L | 2 | SH | UE6110 | 210–355 | 0.10–0.40 | 0.30–2.00 |
| L | 3 | SA | UE6110 | 210–355 | 0.10–0.40 | 0.30–2.00 |
| L | 4 | LP | MP3025 | 195–295 | 0.10–0.40 | 0.30–2.00 |
| L | 5 | SH | NX3035 | 185–260 | 0.10–0.40 | 0.30–2.00 |
Режимы резания: — стабильное резание; — предельное резание; — нестабильное резание.
Области применения: F — финишная обработка; L — чистовая обработка; M — получистовая обработка; R — черновая; H — тяжёлая черновая обработка.