Основной каталог Kyocera 2016-2017 - страница 536

Applicable Toolholders & Inserts In Applicable Toolholder / Insert Lists on J42 〜 J45, Right-hand Insert / Right-hand Toolholder descriptions are listed based on the previous TNN type inserts. For other applicable inserts / toolholders or stock availability of Left-hand, see each relevant page and J48. ■ Parallel Pipe: G(PF), Rp(PS) Nominal Thread External Thread (G) Internal Thread (G,Rp) Same Root’s Symbol TPI Toolholder Insert Toolholder Insert Bore Radius (Previous Symbol) Partial Profile Full Profile Partial Profile Full Profile Dia. G ¹⁄16 16ERA55-TF 6.56 (-) KTNR○○○○□-16 16ERAG55-TF SINR0612S-06E G ¹⁄8 28 KTNSR○○○○□-16 16ERA55 - (EZT J24) 06IR5501 - 0.12 16ERAG55 (HPT J28) 8.57 (PF ¹⁄8) G 1/4 SINR0816S-08E (PF 1/4) 16ERA55-TF (EZT J24) 08IR5501 - 11.45 19 KTNR○○○○□-16 16ERAG55-TF 16ER19W-TF (HPT J28) 0.18 G ³⁄8 KTNSR○○○○□-16 16ERA55 16ER19W SINR1216S-11E 11IRA55 (PF ³⁄8) 16ERAG55 (EZT J24) 11IR55005 - 14.95 (HPT J28) G 1/2 SINR1516S-11 11IR55005 - 18.63 (PF 1/2) SINR1616S-16 G 5⁄8 16ERAG55-TF 20.59 (PF 5⁄8) KTNR○○○○□-16 16ERG55-TF 16ER14W-TF 16IRAG55 G 3/4 14 KTNSR○○○○□-16 16ERAG55 16ER14W SINR2016S-16 16IRG55 16IR14W-TF 0.25 16ERG55 16IR5501 16IR14W 24.12 (PF 3/4) 16IR5502 G 7⁄8 SINR2420S-16 27.88 (PF 7⁄8) J G1 SINR2420S-16 30.29 (PF 1) 16ERAG55-TF 16IRAG55 G 1¹⁄8 11 KTNR○○○○□-16 16ERG55-TF 16ER11W-TF CINR3025S-16 16IRG55 16IR11W-TF 34.94 0.32 (PF 1¹⁄8) KTNSR○○○○□-16 16ERAG55 16ER11W 16IR5501 16IR11W G 11/4 16ERG55 16IR5502 (PF 11/4) CINR3732S-16 38.95 Threading Hereafter, all the threads are 11 TPI and the root’s radius 0.32. The same tool for G1₁⊘₄ is recommended. ■ Tapered Pipe: R, Rc (PT) (BSPT) Nominal Thread External Thread (G) Internal Thread (Rc) Same Root’s Symbol TPI Toolholder Insert Toolholder Insert Radius (Previous Symbol) Partial Profile Full Profile Partial Profile Full Profile R ¹⁄16,Rc ¹⁄16 (16ERA55-TF) (-) KTNR○○○○□-16 (16ERAG55-TF) 16ER28BSPT-TF SINR0612S-06E R ¹⁄8,Rc ¹⁄8 28 KTNSR○○○○□-16 (16ERA55) 16ER28BSPT (EZT J24) 06IR5501 - 0.12 (16ERAG55) (HPT J28) (PT ¹⁄8) R 1/4,Rc 1/4 SINR0816S-08E (PT 1/4) (16ERA55-TF) (EZT J24) 08IR5501 - 19 KTNR○○○○□-16 (16ERAG55-TF) 16ER19BSPT-TF (HPT J28) 0.18 R ³⁄8,Rc ³⁄8 KTNSR○○○○□-16 (16ERA55) 16ER19BSPT SINR1216S-11E (11IRA55) 11IR19BSPT-TF (PT ³⁄8) (16ERAG55) (EZT J24) (11IR55005) 11IR19BSPT (HPT J28) R 1/2,Rc 1/2 SINR1516S-11 (11IR55005) 11IR14BSPT-TF (16ERAG55-TF) 11IR14BSPT (PT 1/2) 14 KTNR○○○○□-16 (16ERG55-TF) 16ER14BSPT-TF SINR1616S-16 0.25 R 3/4,Rc 3/4 KTNSR○○○○□-16 (16ERAG55) 16ER14BSPT 16IR14BSPT-TF (PT 3/4) (16ERG55) SINR2016S-16 16IR14BSPT R 1,Rc 1 (16IRAG55) (PT 1) SINR2420S-16 (16IRG55) (16ERAG55-TF) (16IR5501) R 11/4,Rc 11/4 11 KTNR○○○○□-16 (16ERG55-TF) 16ER11BSPT-TF CINR3025S-16 (16IR5502) 16IR11BSPT-TF 0.32 (PT 11/4) KTNSR○○○○□-16 (16ERAG55) 16ER11BSPT 16IR11BSPT R 11/2,Rc 11/2 (16ERG55) (PT 11/2) CINR3732S-16 Hereafter, all the threads are 11 TPI and the root’s radius 0.32. Hereafter, all the threads are 11 TPI and the root’s radius 0.32. The same tool for R1½ is recommended. The same tool for Rc1½ is recommended. 1) The largest size of minimum diameter toolholder is recommended for internal threading toolholders. Therefore it is available if minimum diameter is smaller than recommended toolholders. (e.g.) SINR2420S-16 (Min. Bore Dia.: φ24mm) is recommended for the Tool of G7/8 Internal Threading from the above Table, but SINR2016S-16 can also be used. 2) When using "Partial Profile" for Tapered Pipe threading, thread's corners become sharp edged, and the shape will not be the same as the standard shape for Tapered Pipe. J42