Каталог Iscar дисковые фрезы и фрезерные пластины 2022 - страница 152

MILLING INSERTS 60° TPMT Triangular 11° Positive Inserts with a Positive Chipformer L Exerting Low Cutting Forces D1 for Internal Finish Turning RE 11° IC S Recommended Dimensions Tough 1 Hard Machining Data f IC520M ap IC8350 IC8250 IC8150 IC50M (mm/ IC830 IC635 IC806 IC807 IC907 IC20 Designation L IC S RE D1 (mm)(1) rev)(2) TPMT 110202 11.00 6.35 2.38 0.20 3.00 • • • 0.20-2.00 0.05-0.25 TPMT 110204 11.00 6.35 2.38 0.40 3.00 • • • • • • 1.00-3.00 0.12-0.30 TPMT 110208 11.00 6.35 2.38 0.80 3.00 • • • • 1.00-4.00 0.15-0.30 TPMT 160304 16.50 9.52 3.18 0.40 4.30 • • • • • • 1.00-4.00 0.12-0.30 TPMT 160308 16.50 9.52 3.18 0.80 4.30 • • • • • • • • • 5.00-12.00 0.15-0.35 • For cutting speed recommendations, see pages 542-547 (1) For turning (2) For turning For tools, see pages: E30 / T230 (36) • E45 / T245 (38) • E60 / T260 (39) PP-R PP-N TPKN/TPKR L 11° Positive Triangular Milling Inserts for General Use BS BS IC S BS Recommended Dimensions Tough 1 Hard Machining Data IC520M ap fz IC50M IC328 IC928 IC250 IC950 IC910 IC20 Designation IC L S BS (mm) (mm/t) TPKN 1603PP-R-42 9.52 16.50 3.18 1.40 • 3.00-10.00 0.10-0.15 TPKN 1603PPFR 9.52 16.50 3.18 1.40 • 3.00-10.00 0.10-0.15 TPKN 1603PPTR 9.52 16.50 3.18 1.40 • • 3.00-10.00 0.10-0.15 TPKN 1603PPTR-42 9.52 16.50 3.18 1.47 • • • 3.00-10.00 0.10-0.15 TPKR 1603PPTR-HS 9.52 16.50 3.50 1.45 • • 3.00-10.00 0.12-0.20 TPKN 2204PDFR 12.70 22.00 4.76 1.40 • 3.00-15.00 0.10-0.15 TPKN 2204PDTR 12.70 22.00 4.76 1.45 • • 3.00-15.00 0.10-0.15 TPKN 2204PDTR-42 12.70 22.00 4.76 1.80 • • • • • • 3.00-15.00 0.10-0.15 TPKR 2204PD-R-76 12.70 22.00 4.76 1.80 • • 3.00-15.00 0.10-0.15 TPKR 2204PDTR-HS 12.70 22.00 4.76 1.88 • • • • 3.00-15.00 0.12-0.20 • For cutting speed recommendations, see pages 542-547 For tools, see pages: F90 (214) IC H690 WNMU 0403 Trigonal Inserts with 6 Rd° Helical Cutting Edges for APMX L 90° Shoulder Milling S BS RE Dimensions Tough 1 Hard Recommended Machining Data IC5400 IC5100 ap fz IC830 IC808 IC810 Designation L APMX IC S RE BS (mm) (mm/t) H690 WNMU 0403-PNTR 4.20 4.00 6.70 3.50 0.40 0.80 • • 0.80-4.00 0.08-0.18 H690 WNMU 0403PNR-MM 4.20 4.00 6.70 3.50 0.40 0.80 • • 0.80-4.00 0.08-0.15 H690 WNMU040308PNR-MM 4.20 4.00 6.70 3.50 0.80 0.40 • • • 1.20-4.00 0.08-0.15 • For cutting speed recommendations, see pages 542-547 For tools, see pages: H690 EWN-04 (12) • H690 EWN-MM-04 (12) • H690 FWN-04 (193) PNTR PNR-MM 468 ISCAR