Режущие и зажимные инструменты Hoffmann Group 2026 - страница 637

GBP 57 POWER MTC CARD GARANT Softcut® high-performance indexable chamfer mill for AP.T 1805.. Robust plug-in chamfer mill. Insert seat enclosed on several sides for stabilisation of the cutters and to take up the vertical and radial forces. tion s figurat r con Application: For wide chamfers in steel fabrications. Outstandingly suitable for roughing and Othe on reques semi-roughing applications. Note: Stepless surfaces are achieved. Use GARANT torque screwdriver TQ No. 211750 size 3.8 with bit No. 674252 size 15IP. l ⌀D ⌀ D1 b Y° γ° 75 60 45 30 15 h Correction factor fz 1 1,2 1,4 2 3,5 Ltot 21 5152 Angle γ 21 5152 Number of Number of Ltot smallest ⌀ largest ⌀ D1 achievable achievable achievable Mounting Feed rate Set of insert screws 21O effective indexable D chamfer chamfer chamfer bore ⌀ per tooth at GARANT Softcut chamfer mill inserts Zeff inserts width b length l height h hmax MTC degrees with bore mm mm mm mm mm mm mm mm ​ 15 eShop 3 6 50 35 92 27.8 29.5 7.5 27 0.4 219808 (15IP; 3.8 Nm) 30 eShop 3 6 50 35 85 24.3 29.5 14 27 0.2 219808 (15IP; 3.8 Nm) 45 eShop 3 6 50 35 76 20 29.5 20 27 0.14 219808 (15IP; 3.8 Nm) 60 eShop 3 6 50 35 64 14 29.5 24.3 27 0.12 219808 (15IP; 3.8 Nm) 75 eShop 3 6 60 35 50 7.5 29.5 27.8 22 0.11 219808 (15IP; 3.8 Nm) POWER MTC CARD 90° GARANT Softcut® high-performance indexable shoulder mill 90° MTC for indexable inserts AP.T 1805.. High precision square shoulder milling cutter with irregular pitch for very smooth cutting, very high precision and cutting power. High performance indexable square shoulder milling cutter with special geometry for reduced cutting forces for MTC applications under unstable conditions or for spindles with low drive power. Application: For face milling to large depths, also slotting. General use in all steels including stainless steels. Especially for MTC (Multi Task Cutting) use on the new generation of turning / milling centres (MTM). Note: The insert pocket must be modified when using indexable inserts with a radius greater than 3.1 mm. Use GARANT torque screwdriver TQ No. 211750 size 3.8 with bit No. 674252 size 15IP. 21 Single-row ​ 21 5157 – Without internal cooling. ap ⌀D ⌀ DS Dmin L1 Dmax Ltot 21 5155 ⌀ D / number 21 5155 21 5157 L1 Ltot ⌀ Ds Circular Circular Circular Ramping Ramping suitable Set of insert screws 21O 21O of teeth Z h6 interpola- interpola- interpola- angle αmax length L for indexable tion milling tion milling tion milling αmax insert GARANT Softcut 90° shoulder mill ⌀ Dmin ⌀ Dmax ap 21 5155 21 5157 21 5155 21 5157 ​ MTC short MTC long Weldon shank Plain shank mm mm mm mm mm mm mm mm mm degrees mm ​ ​ 25/2 eShop eShop 44 45 100 200 25 44 48 1 1.69 16.95 AP.. 1805.. 219824 (15IP; 3.8 Nm) 32/3 eShop eShop 50 50 110 250 32 58 62 1 1.2 23.95 AP.. 1805.. 219824 (15IP; 3.8 Nm) 40/4 eShop – 55 – 115 – 32 74 78 1 0.9 31.95 AP.. 1805.. 219808 (15IP; 3.8 Nm) 637