Общий каталог Dijet 2018 - страница 63
Навигация
Общий каталог Dijet 2012 на русском
Tooling by DIJET
Modular Head Series
QM MAX MQXTYPE
■ RECOMMENDED CUTTING CONDITIONS/LOW DEPTH OF CUT AND HIGH FEED
● MQX type (ZPMT 100320ZER insert) + MSN Carbide Shank Holder
Too ldia. (mm)
Work Insert
40/42 40
Materials Grades No. of teeth 6N No. oft eeth 7N
ℓ ap ae Vf
n(min ) (mm/min)
-1
ℓ ap ae n Vf
(mm) (mm) (mm) (mm) (mm) (mm) (min-1) (mm/min)
Carbon steel ~100 0.4 ~32 1,350 4,860 ~100 0.4 ~32 1,350 5,670
S50C, S55C JC5118
(C50, C55) (JC8050) 150 0.35 ~32 1,350 4,860 150 0.35 ~32 1,350 5,670
Below 250HB 210 0.3 ~32 1,220 3,940 210 0.3 ~32 1,220 4,590
Die steel ~100 0.4 ~32 1,270 4,570 ~100 0.4 ~32 1,270 5,330
SKD61, SKD11 JC5118
(1.2344,1.2379) (JC8050) 150 0.35 ~32 1,270 4,570 150 0.35 ~32 1,270 5,330
Below 255HB 210 0.3 ~32 1,140 3,700 210 0.3 ~32 1,140 4,320
Mold steel ~100 0.4 ~32 1,270 4,570 ~100 0.4 ~32 1,270 5,330
HPM7, PX5, P20 JC8050
(1.2311, P20) (JC5118) 150 0.35 ~32 1,270 4,570 150 0.35 ~32 1,270 5,330
30-36HRC 210 0.3 ~32 1,140 3,700 210 0.3 ~32 1,140 4,320
Grey & Nodular ~100 0.4 ~32 1,190 5,000 ~100 0.4 ~32 1,190 5,830
cast iron
FC, FCD JC5118 150 0.35 ~32 1,190 5,000 150 0.35 ~32 1,190 5,830
(GG, GGG)
Below 300HB 210 0.3 ~32 1,070 4,050 210 0.3 ~32 1,070 4,720
~100 0.4 ~32 1,350 4,860 ~100 0.4 ~32 1,350 5,670
Stainless steel
SUS304 JC8050 150 0.35 ~32 1,350 4,860 150 0.35 ~32 1,350 5,670
Below 250HB
210 0.3 ~32 1,220 3,940 210 0.3 ~32 1,220 4,590
~100 0.3 ~32 480 1,150 ~100 0.3 ~32 480 1,350
Titanium alloy JC5118
(Ti-6Al-4V) (JC8050) 150 0.25 ~32 480 1,150 150 0.25 ~32 480 1,350
210 0.2 ~32 480 1,150 210 0.2 ~32 480 1,350
~100 0.3 ~32 250 450 ~100 0.3 ~32 250 520
Inconel JC5118
(INCO718) (JC8050) 150 0.25 ~32 250 450 150 0.25 ~32 250 520
210 0.2 ~32 250 450 210 0.2 ~32 250 520
ℓ: Overhung length, ap: Axial depth of cut, ae: Radial depth of cut, n: Spindle speed, Vf: Feed speed
■ NOTE
1) The cutting parameters to be adjusted according to the machine rigidity or work rigidity.
2) In case chatter occurrs, recommend to reduce depth of cut or spindle speed with keeping feed per tooth.
3) If machine does not have enough power, recommend to reduce depth of cut first and reduce spindle speed and
feed speed.
4) Use air blow to flush the chips out. B047
Modular Head Series
QM MAX MQXTYPE
■ RECOMMENDED CUTTING CONDITIONS/LOW DEPTH OF CUT AND HIGH FEED
● MQX type (ZPMT 100320ZER insert) + MSN Carbide Shank Holder
Too ldia. (mm)
Work Insert
40/42 40
Materials Grades No. of teeth 6N No. oft eeth 7N
ℓ ap ae Vf
n(min ) (mm/min)
-1
ℓ ap ae n Vf
(mm) (mm) (mm) (mm) (mm) (mm) (min-1) (mm/min)
Carbon steel ~100 0.4 ~32 1,350 4,860 ~100 0.4 ~32 1,350 5,670
S50C, S55C JC5118
(C50, C55) (JC8050) 150 0.35 ~32 1,350 4,860 150 0.35 ~32 1,350 5,670
Below 250HB 210 0.3 ~32 1,220 3,940 210 0.3 ~32 1,220 4,590
Die steel ~100 0.4 ~32 1,270 4,570 ~100 0.4 ~32 1,270 5,330
SKD61, SKD11 JC5118
(1.2344,1.2379) (JC8050) 150 0.35 ~32 1,270 4,570 150 0.35 ~32 1,270 5,330
Below 255HB 210 0.3 ~32 1,140 3,700 210 0.3 ~32 1,140 4,320
Mold steel ~100 0.4 ~32 1,270 4,570 ~100 0.4 ~32 1,270 5,330
HPM7, PX5, P20 JC8050
(1.2311, P20) (JC5118) 150 0.35 ~32 1,270 4,570 150 0.35 ~32 1,270 5,330
30-36HRC 210 0.3 ~32 1,140 3,700 210 0.3 ~32 1,140 4,320
Grey & Nodular ~100 0.4 ~32 1,190 5,000 ~100 0.4 ~32 1,190 5,830
cast iron
FC, FCD JC5118 150 0.35 ~32 1,190 5,000 150 0.35 ~32 1,190 5,830
(GG, GGG)
Below 300HB 210 0.3 ~32 1,070 4,050 210 0.3 ~32 1,070 4,720
~100 0.4 ~32 1,350 4,860 ~100 0.4 ~32 1,350 5,670
Stainless steel
SUS304 JC8050 150 0.35 ~32 1,350 4,860 150 0.35 ~32 1,350 5,670
Below 250HB
210 0.3 ~32 1,220 3,940 210 0.3 ~32 1,220 4,590
~100 0.3 ~32 480 1,150 ~100 0.3 ~32 480 1,350
Titanium alloy JC5118
(Ti-6Al-4V) (JC8050) 150 0.25 ~32 480 1,150 150 0.25 ~32 480 1,350
210 0.2 ~32 480 1,150 210 0.2 ~32 480 1,350
~100 0.3 ~32 250 450 ~100 0.3 ~32 250 520
Inconel JC5118
(INCO718) (JC8050) 150 0.25 ~32 250 450 150 0.25 ~32 250 520
210 0.2 ~32 250 450 210 0.2 ~32 250 520
ℓ: Overhung length, ap: Axial depth of cut, ae: Radial depth of cut, n: Spindle speed, Vf: Feed speed
■ NOTE
1) The cutting parameters to be adjusted according to the machine rigidity or work rigidity.
2) In case chatter occurrs, recommend to reduce depth of cut or spindle speed with keeping feed per tooth.
3) If machine does not have enough power, recommend to reduce depth of cut first and reduce spindle speed and
feed speed.
4) Use air blow to flush the chips out. B047