Indexable Tools θ° ap Tool dia. φDc Tooling by DIJET High Feed Diemaster SKSTyPE ■ Instructions for profile milling ● Ramping ● Helical interpolation ● Calculation of tool pass dia. L φDh φdc = φDh – φDcTool pass dia.Bore dia. Tool dia. ● Depth of cut per one circle should not exceed max. depth of cut ap. ● Down cutting is recommended & tool pass rotation should be counterclockwise. φdc ● In case of ramping and helical interpolation, apply 70% or less feed speed from standard cutting condition table. ● In case of drilling, apply 50% or less Z axis feed speed from standard cutting condition table. ● Long continous chips may come out in case of drilling, confirm the safe cutting conditions. Tool Effective Max. depth Ramping Helical interpolation Cat. No. dia. cuttingφDcdia.(mm)(mm)of cutap(mm) Max. drillingMax.Total cutting length L (mm)Min. bore dia.Max. bore dia.depthrampingat max.apDh min (mm)Dh max (mm)(mm)angle θ° SKS-2016 16 10.5 0.8 2°30′ 20.6 25 29 0.3 SKS-2017 17 11.5 0.8 2° 25.7 27 31 0.3 SKS-2020 20 12.7 1.2 3° 22.9 30 37 0.5 SKS-2021 21 13.7 1.2 2°30′ 27.5 32 39 0.5 SKS-2025 25 15.9 1.5 4° 21.5 33 46 1 SKS-2026 26 16.9 1.5 3°30′ 24.5 35 48 1 SKS-2030 30 20.9 1.5 2°30′ 34.4 43 56 1 SKS-2032 32 20 2 4° 28.6 41 60 1.5 SKS-3032 32 22.8 1.5 2°15′ 38.1 47 60 1 SKS-3040-06 40 30.8 1.5 1°36′ 53.7 63 76 1 SKS-*050 50 38 2 2° 57.3 77 96 1.5 SKS-3050-*-10 50 35.1 2.3 2°18′ 57.3 71 96 1.8 SKS-5050-06 50 40.8 1.5 1°09′ 59.8 83 96 1 SKS-*052 52 40 2 2° 57.3 81 100 1.5 SKS-5052-06 52 42.8 1.5 1°06′ 62.5 87 100 1 SKS-*063 63 51 2 1°30′ 76.4 103 122 1.5 SKS-*063-10 63 48 2.3 2°24′ 48.8 97 122 1.8 SKS-*066 66 54 2 1°42′ 81.8 109 128 1.5 SKS-*080 80 68 2 1°12′ 95.5 137 156 1.5 SKS-*080-10 80 65 2.3 2° 65.9 131 156 1.8 SKS-*100 100 88 2 1° 114.6 177 196 1.5 SKS-*100-10 100 85 2.3 1°30′ 87.8 171 196 1.8 SKS-*125-10 125 110 2.3 1°12′ 109.8 221 246 1.8 SKS-*160-10 160 145 2.3 0°54′ 146.4 291 316 1.8 C041