”Wave Mill” Series WFXH - M Type New General Features WaveMill WFXH type is a high efficiency, multi-purpose cutter, that uses the WFX series inserts for high-feed roughing and a variety of processes. Characteristics Stable, high-efficiency milling with superior cutting edge sharpness. Supports various types of processes (ramping and helical milling). Able to use the selection of inserts from the WFX series. Notes on Corner Finishing - Remaining Material Actual machined corners will have uncut and overcut portions due to the shape of the inserts. Fig. 1 Fig. 2 Overcut Portion Uncut Portion Uncut Portion Programmed Programmed Corner R Corner R WFXH 08000 Type Programmed SOMT 08 04- SOMT 08 08- SOMT 08 12- Corner R Uncut Portion Overcut Portion Shape Uncut Portion Overcut Portion Shape Uncut Portion Overcut Portion Shape 2,0 1,41 0 Fig. 1 1,30 0 Fig. 1 1,21 0 Fig. 1 2,5 1,30 0,02 Fig. 2 1,19 0,01 Fig. 2 1,09 0 Fig. 2 3,0 - - - - - - 0,98 0,05 Fig. 2 WFXH 12000 Type Programmed SOMT 12 04- SOMT 12 08- SOMT 12 12- SOMT 12 16- Corner R Uncut Portion Overcut Portion Shape Uncut Portion Overcut Portion Shape Uncut Portion Overcut Portion Shape Uncut Portion Overcut Portion Shape 2,0 2,58 0 Fig. 1 2,48 0 Fig. 1 2,37 0 Fig. 1 2,25 0 Fig. 1 2,5 2,47 0 Fig. 1 2,37 0 Fig. 1 2,25 0 Fig. 1 2,14 0 Fig. 1 3,0 2,36 0 Fig. 1 2,26 0 Fig. 1 2,14 0 Fig. 1 2,11 0 Fig. 1 3,5 2,24 0,01 Fig. 2 2,14 0 Fig. 1 2,03 0 Fig. 1 1,91 0 Fig. 1 4,0 - - - 2,03 0,04 Fig. 2 1,91 0,03 Fig. 2 1,8 0,01 Fig. 2 Minimum Cutting Diameter Minimum cutting diameter (DCN) will depend on the insert that is used. Using an insert with a large nose radius is recommen- ded for the WFXH type. ØDb Ød a Body Cat. No. ØDc DCN based on insert noseR0,4R0,8R1,2R1,6 WFXH 08025 M 25 9,69 9,48 9,27 - 08032 M 32 16,6 16,4 16,2 - WFXH 12040 M 40 15,8 15,5 15,3 15,1 Ød2 Ød1 DCN ØDc Taper Cutting and Helical Milling Minimum Diameter Maximum Diameter Insert Cat. No. ØDc Helical Millilng Taper Cutting Min. Max. Max. Ramping Angle SOMT 08 04- 25 35 49 1°30‘ 32 49 63 0°30‘ SOMT 08 08- 25 35 48 3° Minimum and Maximum Diameters 32 49 62 1°30‘ SOMT 08 12- 25 34 47 4°30‘ 32 48 61 2°30‘ SOMT 12 04- 40 56 79 1° Ramping Angle SOMT 12 08- 40 56 78 1°30‘ SOMT 12 12- 40 55 77 2°30‘ Ramping Angle SOMT 12 16- 40 55 76 3°30‘ H12 l = Euro stock  G44 Recommended Tightening Torque (N·m) Indexable Endmills b Lf