Общий каталог SGS 2021 - страница 114

FRACTIONAL Series 27 Ap Series Ae Ae DC • in 27 Vc Fractional Ae x DC Ap x DC (sfm) 1/4 3/8 1/2 3/4 Slot 400 RPM 6112 4075 3056 2037 1 ≤1 Fz 0.0016 0.0030 0.0040 0.0048 (320-480) Feed (ipm) 39 49 49 39 500 RPM 7640 5093 3820 2547 CFRP, AFRP Profile (CARBON FIBER, ≤ 0.5 ≤ 1.5 Fz 0.0016 0.0030 0.0040 0.0048 ARAMID FIBER) (400-600) Feed (ipm) 49 61 61 49 HSM 825 RPM 12606 8404 6303 4202 ≤ 0.5 ≤2 Fz 0.0037 0.0069 0.0092 0.0110 (660-990) Feed (ipm) 187 232 232 185 Slot 320 RPM 4890 3260 2445 1630 1 ≤1 Fz 0.0016 0.0030 0.0040 0.0048 (256-384) Feed (ipm) 31 39 39 31 GFRP(FIBERGLASS) Profile 400 RPM≤ 0.5≤ 1.5Fz(320-480)61120.0016 40750.0030 30560.0040 20370.0048 Feed (ipm) 39 49 49 39 HSM 660 RPM 10085 6723 5042 3362 ≤ 0.5 ≤2 Fz 0.0037 0.0069 0.0092 0.0110 (528-792) Feed (ipm) 149 186 186 148 Slot 480 RPM 7334 4890 3667 2445 1 ≤1 Fz 0.0020 0.0038 0.0050 0.0060 (384-576) Feed (ipm) 59 74 73 59 Profile 600 RPM 9168 6112 4584 3056 N CARBON, GRAPHITE ≤ 0.5 ≤ 1.5 Fz 0.0020 0.0038 0.0050 0.0060 (480-720) Feed (ipm) 73 93 92 73 HSM 990 RPM 15127 10085 7564 5042 ≤ 0.5 ≤2 Fz 0.0046 0.0086 0.0115 0.0138 (792-1188) Feed (ipm) 278 347 348 278 Slot 800 RPM 12224 8149 6112 4075 1 ≤1 Fz 0.0020 0.0038 0.0050 0.0060 (640-690) Feed (ipm) 98 124 122 98 Profile 1000 RPM 15280 10187 7640 5093 PLASTICS ≤ 0.5 ≤ 1.5 Fz 0.0020 0.0038 0.0050 0.0060 (800-1200) Feed (ipm) 122 155 153 122 HSM 1650 RPM 25212 16808 12606 8404 ≤ 0.5 ≤2 Fz 0.0046 0.0086 0.0115 0.0138 (1320-1980) Feed (ipm) 464 578 580 464 Slot 40 RPM 611 407 306 204 1 ≤1 Fz 0.0008 0.0015 0.0020 0.0024 (32-48) Feed (ipm) 2.0 2.4 2.4 2.0 MACHINABLE Profile 50 RPM 764 509 382 255 CERAMICS ≤ 0.5 ≤ 1.5 Fz 0.0008 0.0015 0.0020 0.0024 MACHINABLE GLASS (40-60) Feed (ipm) 2.4 3.1 3.1 2.4 HSM 85 RPM 1299 866 649 433 ≤ 0.5 ≤2 Fz 0.0018 0.0034 0.0046 0.0055 (68-102) Feed (ipm) 9.4 11.8 11.9 9.5 HSM (High Speed Machining) rates shown are for use without coolant; rates may be increased with coolant rpm = Vc x 3.82 / DC dust collection is vital when machining dry ipm = Fz x 4 x rpm diamond coating will increase tool life in graphite and composite materials adjust parameters based on resin type and fiber structure feed rates listed have chip thinning adjustments included where applicable reduce speed when overheating causes melting or damage to resin refer to the SGS Tool Wizard® for complete technical information reduce feed if delamination or fraying occur   (www.kyocera-sgstool.com) finish cuts typically required reduced feed and cutting depthsv 114 END MILLS wwwE.kNyDoMceILraLS-sgstool.com