Общий каталог SGS 2018 - страница 39

FRACTIONAL Z-Carb-AP Ap Series Diameter (D1) Z1PCR, Z1PLC, Ae Ae (inch) Z1PLB Vc Fractional Hardness Ae x D1 Ap x D1 (sfm) 1/64 1/8 1/4 3/8 1/2 5/8 3/4 1 340 RPM 83256 10390 5195 3463 2598 2078 1732 1299 Profile ≤ 0.5 ≤ 1.5 Fz 0.00003 0.00027 0.0007 0.0014 0.0018 0.0020 0.0022 0.0025 (272-408) STAINLESS STEELS ≤ 275 Bhn Feed (ipm) 10.0 11.2 14.5 19.4 18.7 16.6 15.2 13.0 (DIFFICULT) or 304, 304L, 316, 316L ≤ 28 HRc 270 RPM 66115 8251 4126 2750 2063 1650 1375 1031 Slot 1 ≤1 Fz 0.00003 0.00027 0.0007 0.0014 0.0018 0.0020 0.0022 0.0025 (216-324) Feed (ipm) 7.9 8.9 11.6 15.4 14.9 13.2 12.1 10.3 M 310 RPM 75910 9474 4737 3158 2368 1895 1579 1184 Profile ≤ 0.5 ≤ 1.5 Fz 0.00003 0.00027 0.0007 0.0014 0.0018 0.0020 0.0022 0.0025 STAINLESS STEELS (248-372) (PH) ≤ 325 Bhn Feed (ipm) 9.1 10.2 13.3 17.7 17.1 15.2 13.9 11.8 13-8 PH, 15-5 PH, or 17-4 PH, Custom 450 ≤ 35 HRc 250 RPM 61218 7640 3820 2547 1910 1528 1273 955 Slot 1 ≤1 Fz 0.00003 0.00027 0.0007 0.0014 0.0018 0.0020 0.0022 0.0025 (200-300) Feed (ipm) 7.3 8.3 10.7 14.3 13.8 12.2 11.2 9.6 80 RPM 19590 2445 1222 815 611 489 407 306 Profile ≤ 0.5 ≤ 1.5 Fz 0.00003 0.00025 0.0007 0.0013 0.0017 0.0019 0.0020 0.0024 SUPER ALLOYS (64-96) (NICKEL, COBALT, ≤ 300 Bhn Feed (ipm) 2.4 2.4 3.3 4.2 4.2 3.7 3.3 2.9 IRON BASE) or Inconel 601, 617, 625, ≤ 32 HRc 65 RPM 15917 1986 993 662 497 397 331 248 Incoloy, Monel 400 Slot 1 ≤1 Fz 0.00003 0.00025 0.0007 0.0013 0.0017 0.0019 0.0020 0.0024 (52-78) Feed (ipm) 1.9 2.0 2.7 3.4 3.4 3.0 2.7 2.4 62 RPM 15182 1895 947 632 474 379 316 237 Profile SUPER ALLOYS ≤ 0.5 ≤ 1.5 Fz 0.00002 0.00018 0.0005 0.0009 0.0012 0.0013 0.0014 0.0017 (NICKEL, COBALT, (50-74) IRON BASE) ≤ 400 Bhn Feed (ipm) 1.2 1.4 1.8 2.3 2.3 2.0 1.8 1.6 Inconel 718, X-750, or Incoloy, Waspaloy, ≤ 43 HRc 50 RPM 12244 1528 764 509 382 306 255 191 Hastelloy, Rene Slot 1 ≤1 Fz 0.00002 0.00018 0.0005 0.0009 0.0012 0.0013 0.0014 0.0017 (40-60) Feed (ipm) 1.0 1.1 1.5 1.8 1.8 1.6 1.4 1.3 S 215 RPM 52647 6570 3285 2190 1643 1314 1095 821 Profile ≤ 0.5 ≤ 1.5 Fz 0.00003 0.0003 0.0008 0.0015 0.0020 0.0022 0.0024 0.0028 TITANIUM ALLOYS (172-258) Pure Titanium, ≤ 350 Bhn Feed (ipm) 6.3 7.9 10.5 13.1 13.1 11.6 10.5 9.2 Ti6Al4V, or Ti6Al2Sn4Zr2Mo, ≤ 38 HRc 170 RPM 41628 5195 2598 1732 1299 1039 866 649 Ti4Al4Mo2Sn0.5Si Slot 1 ≤1 Fz 0.00003 0.0003 0.0008 0.0015 0.0020 0.0022 0.0024 0.0028 (136-204) Feed (ipm) 5.0 6.2 8.3 10.4 10.4 9.1 8.3 7.3 75 RPM 18365 2292 1146 764 573 458 382 287 TITANIUM ALLOYS Profile (DIFFICULT) ≤ 0.5 ≤ 1.5 Fz 0.00003 0.0003 0.0008 0.0015 0.0020 0.0022 0.0024 0.0028 Ti10Al2Fe3Al, (60-90) Ti5Al5V5Mo3Cr, ≤ 440 Bhn Feed (ipm) 2.2 2.8 3.7 4.6 4.6 4.0 3.7 3.2 Ti7Al4Mo, or Ti3Al8V6Cr4Zr4Mo, ≤ 47 HRc 60 RPM 14692 1834 917 611 458 367 306 229 Ti6Al6V6Sn, Ti15V3 Slot Cr3Sn3Al 1 ≤1 Fz 0.00003 0.0003 0.0008 0.0015 0.0020 0.0022 0.0024 0.0028 (48-72) Feed (ipm) 1.8 2.2 2.9 3.7 3.7 3.2 2.9 2.6 Bhn (Brinell)   HRc (Rockwell C) rpm = Vc x 3.82 / D1 ipm = Fz x 4 x rpm maximum Slotting Ap for Z1PCR <1/8 diameter and all Z1PLC / Z1PLB is .25 x D1 maximum Profile Ae for Z1PCR <1/8 diameter and all Z1PLC / Z1PLB is .20 x D1 reduce speed and feed for materials harder than listed reduce feed and Ae when finish milling (.02 x D1 maximum) refer to the KYOCERA SGS Tool Wizard® for complete technical information (www.kyocera-sgstool.com) www.kyocerEaN-DsgMstILoLoSl.com END MILLS 39