Общий каталог Mitsubishi 2020 - 2021 - страница 1230

• C009A_CUTTING TOOLS
• INDEX
• A_TURNING INSERTS
• B_CBN & PCD TURNING INSERTS
• C_EXTERNAL TURNING TOOLS
• D_SMALL TOOLS
• E_BORING BARS
• F_GROOVING/CUTTING OFF
• G_THREADING
• H_HSK-T TOOLS
• I_SOLID CARBIDE END MILLS
• J_EXCHANGEABLE HEAD END MILLS
• K_ROTATING TOOL INSERTS
• L_INDEXABLE MILLING
• M_DRILLING
• N_SPARE PARTS
• P_TECHNICAL DATA

y Wet Cutting (inch) Work Material Hardness Breaker Grade vc(SFM) fz(IPT) ap ae M Austenitic Stainless Steel < 200HB MP7030 MM 410 (330 ─ 490) .006 (.004 ─ .008) < .197 < 0.8DC Austenitic Stainless Steel > 200HB MP7030 MM 330 (245 ─ 410) .006 (.004 ─ .008) < .197 < 0.8DC Two-phase Stainless Steel < 280HB MP7030 MM 260 (195 ─ 330) .004 (.002 ─ .006) < .197 < 0.8DC Ferritic and MaltensiticStainless Steel< 200HB MP7030 MM 410 (330 ─ 490) .006 (.004 ─ .008) < .197 < 0.8DC Ferritic and MaltensiticStainless Steel> 200HB MP7030 MM 330 (245 ─ 410) .006 (.004 ─ .008) < .197 < 0.8DC Precipitation HardeningStainless Steel< 450HB MP7030 MM 230 (165 ─ 295) .004 (.002 ─ .006) < .197 < 0.8DC S ─ MP7030 MM 130 (65 ─ 165) .006 (.004 ─ .008) < .118 < 0.6DC Titanium Alloy ─ MP9120 L 195 (165 ─ 230) .004 (.002 ─ .006) < .118 < 0.6DC ─ MP9130 L 130 (65 ─ 165) .006 (.004 ─ .008) < .118 < 0.6DC ─ MP7030 MM 130 (65 ─ 165) .006 (.004 ─ .008) < .118 < 0.6DC Heat Resistant Alloy ─ MP9120 L 195 (165 ─ 230) .004 (.002 ─ .006) < .118 < 0.6DC ─ MP9130 L 130 (65 ─ 165) .006 (.004 ─ .008) < .118 < 0.6DC Note1) Recommended wet cutting for good surface finishing of stainless steel. (Tool life is short compared to wet cutting.) Note2) We recommend wet cutting with internal coolant for titanium alloy and heat resistant alloy. Note3) When clamp rigidity is low and tool overhang is long, we recommended to reduce the cutting speed and the feed rate by 30%. y Cutting Conditions with Wiper Insert (inch) Work Material Hardness MainInsertGrade WiperInsertGrade vc(SFM) fz(IPT) ap ae P VP15TF MP VP15TF WP 820 (655 ─ 985) .012 (.008 ─ .016) < .0197 < 0.8DC Mild Steel < 180HB MP6120 M MP6120 M 820 (655 ─ 985) .012 (.008 ─ .016) < .0197 < 0.8DC VP15TF MP VP15TF WP 720 (560 ─ 885) .012 (.008 ─ .016) < .0197 < 0.8DC Carbon Steel,Alloy Steel 180 ─ 280HB MP6120 M MP6120 M 720 (560 ─ 885) .012 (.008 ─ .016) < .0197 < 0.8DC VP15TF MP VP15TF WP 460 (330 ─ 590) .012 (.008 ─ .016) < .0197 < 0.8DC Carbon Steel,Alloy Steel 280 ─ 350HB MP6120 M MP6120 M 460 (330 ─ 590) .012 (.008 ─ .016) < .0197 < 0.8DC K Tensile MC5020 MK,HK MC5020 WK 1050 (820 ─ 1310) .012 (.008 ─ .016) < .0197 < 0.8DC Gray Cast Iron Strength < 350MPa VP15TF MP VP15TF WP 720 (490 ─ 985) .012 (.008 ─ .016) < .0197 < 0.8DC L Tensile MC5020 MK,HK MC5020 WK 820 (655 ─ 985) .008 (.004 ─ .012) < .0197 < 0.8DC Ductile Cast Ilon Strength < 450MPa VP15TF MP VP15TF WP 655 (490 ─ 820) .008 (.004 ─ .012) < .0197 < 0.8DC Tensile MC5020 MK,HK MC5020 WK 720 (655 ─ 820) .008 (.004 ─ .012) < .0197 < 0.8DC Ductile Cast Ilon Strength < 800MPa VP15TF MP VP15TF WP 560 (490 ─ 655) .008 (.004 ─ .012) < .0197 < 0.8DC S Heat Resistant Alloy ─ VP15TF MP VP15TF WP 130 (65 ─ 165) .006 (.004 ─ .008) < .0197 < 0.8DC H Hardened Steel 40 ─ 55HRC VP15TF MP VP15TF WP 260 (195 ─ 330) .006 (.004 ─ .008) < .0197 < 0.8DC Note 1) When clamp rigidity is low and tool overhang is long, we recommended to reduce the cutting speed and the feed rate by 30%. Note 2) Please use WP geometry insert in combination with MP or M geometry inserts, and use WK geometry insert in combination with MK or HK geometry inserts L055 INDEXABLE MILLING